Reference: 205.0001
POLINI segment in L Ø48mm X 2mm for aluminum POLINI kit
Ideal for a refurbishment of your high engine.
Banner
The enthusiasts dreamed it, POLINI did it, the famous POLINI SERIE 6000 kit remade for your old SACHS motorcycle engines. This kit is really complete, it has an exhaust pipe internal diameter 29.5mm and external 32.20mm.
An intake pipe with its flexible sleeve internal diameter 19mm, external diameter for rigid carburetor of 24mm, and diameter of the flexible sleeve of 35mm internally for flexible carburetors, if you install a flexible carburetor with this sleeve, you will cut the intake pipe at the inlet, its diameter will then increase to about 25mm.
It is ideal for the installation of a 25mm POLINI, DELLORTO PHBH, PHBL, VHST ... The cylinder is in high quality aluminum with nikasil coating, it has 2 rear transfers which are also used for filling the lower engine that will come then feed the laterals.
It is therefore ultimately a real 4 transfers because the 2 rear does not come into action for the PISTON sweep unlike the AM6, DERBI ... The exhaust is a large oval. The housing inlet skirt diameter is Ø53mm, so a 53.2mm reamed housing is needed. Between axis of the studs 80X80mm.
The piston is a model with high silicon content, with L segment. The delivered cylinder head has a very worked combustion chamber, hemispherical, micro-blasted finish. It has a reinforcing bar in the mold to prevent curtains.
In view of the quality of aluminum, do not be afraid of cooling, this cylinder will not exceed the temperature required for performance! It will give you a lot of torque and power given that it is designed for 44mm stroke. And you will therefore leave fresh with your good old SACHS motorcycle. It is really a superb set that has emerged POLINI, in limited series!
Summary:
For SACHS Motorcycle Engine
For stroke: 44mm
Skirt diameter Ø53mm, perfect crankcase bore 53.2mm
Transfers: 2 rear for low engine filling, 4 side real ones.
Exhaust: Standard oval Piston: single-segment, with L-type segment
Cylinder head: high compression microblasted hemispherical chamber
Intake pipe: For 19mm rigid or 25mm flexible (+ if pipe preparation)
Between-axis studs 80X80mm
Exhaust pipe delivered internal Ø29.5mm and external 32.2mm
Advertised power: 13.6hp at 9800 revolutions per minute
As an option we offer you a stage 1 preparation, this preparation is a modification of the channels and the exhaust port by increasing the diagrams and improving the duct, it increases the performance of the cylinder. An improvement to the piston and the bottom of the skirt is also included in this modification. Allow a little extra time for this preparation!
Specific References
Reference: 205.0001
Ideal for a refurbishment of your high engine.
Reference: 216.0101
The POLINI exhaust tube for your old mopeds has gearbox.
Reference: 215.0190
An ideal intake pipe because it can take a lot of carburetors and is changeable!
Reference: 204.0004/A
Ideal to maintain your kit POLINI on SACHS in race 44mm.
Reference: 209.0153
Ideal to maintain your high engine POLINI S 6000 on SACHS.
Reference: 271.0003
Piston pin Ø14mm for engine THOR or S6000 on SACH.
Reference: 85207.00
The complete kit 70cc for ZUNDAPP with its cylinder head!
Reference: 003100
Very torquey, robust and powerful kit for ZUNDAPP!
Reference: 020000
The ATHENA cylinder, piston, cylinder head, Ø48mm kit for SACHS CORSA LUNGA 50.
Reference: 85438.00
A 70cc kit for ZUNDAPP air cooling for miniterm engines.
Reference: 063600
ZUNDAPP is very robust and powerful!
Reference: 148.6008
The POLINI 6000 series kit reproduced for enthusiasts! For 39.6mm stroke.
Reference: 25104.00
PARMAKIT 80cc special kit for old FANTIC CABALLERO. 48X48mm studs.
Reference: 85206.00
The piston-cylinder without cylinder head 70cc for ZUNDAPP air cooling as the CS50, KS50 ...
Reference: 85307.00
A 70cc kit for ZUNDAPP air cooling for miniterm engines.
Reference: 64430.00
A high-performance and full high special range for motor SACHS 503 and 504 in axis of 12mm with 2 transfers with a long stroke crankshaft.
Reference: 168.6006
The POLINI SERIE 6000 kit reproduced for enthusiasts! For 41.6mm stroke.
Reference: 85465.00
kit Ø45mm 70cc for ZUNDAP 50 air cooling, admission without valves on cylinder.
Reference: 85306.00
The piston-cylinder without cylinder head 70cc for ZUNDAPP air cooling for miniterm engines.
Reference: 021700
The cylinder kit, piston, cylinder head, Ø48mm ATHENA for P4R, MACAL, MALAGUTI FIFTY ....
Reference: 53490.00
A high-performance top special range 42mm stroke motor Minarelli P6! Exhaust mounting by 3 screws for RADIAL SYSTEM.
Reference: 007100
ZUNDAPP is very robust and powerful!