
Reference: 64266.16
PARMAKIT segment in L Ø48mm X 2mm for VERTEX mono segment piston on MINARELLI P6
High-end segment to refurbish and increase your engine compression!
Banner
A set of rare performance parts for old motorcycles engine MINARELLI P6 air cooling. With PARMAKIT everything is possible, the proof image!
This cylinder made of high quality aluminum straight out of molds made in Italy! It has 4 large intake transfers with internal lubrication system to the cylinder and in line with its piston.
The architecture and finish are excellent course and upscale. A huge exhaust with bar charts and high engine make this group a powerful asset to your 2 wheels!
The piston accompanying this cylinder is a single-segment model in VERTEX therefore high quality with preparation on the rear top portion of the piston to improve the lubrication and scanning in the cylinder and low engine. With his segment L will offer you the highest regimes maximizing top speed and climb the towers!
The other feature of this cylinder is the opportunity to ask for the 42mm race with shim aluminum 3mm provided thus increasing the capacity. Clearly, a quality / price / excellent performance to increase dramatically the power of your motorcycle engine Minarelli P6!
Fixing exhaust by 3 studs securing admission has a pitch of 52mm. We recommend to accompany this kit with at least a 21mm carburetor, racing cold plug, engine oil 100% synthetic racing, bearings and reinforced crankshaft, racing exhaust ....
This pack contains:
Aluminum master cylinder 4 transfers with exhaust with bar
-piston VERTEX single segment with high back preparing for greasing
-Segment L x 2mm Ø48mm chrome steel
Axis-piston Ø12 X 42mm
Crab-like piston -Clips
-pack Engine seals
-Cale Of 3mm aluminum base
-Notice
-Autocollant
Parmakit plan for this engine MINARELLI P6 RADIAL SISTEM-in 42mm stroke.
Optional we offer a preparation course 1, this preparation is a modification of the channels and the exhaust port by increasing the charts and improvement of the duct, it increases the cylinder performance. Improved piston and bottom skirt is also included in the amendment. Allow a little extra time for this preparation!
Reference: 64266.16
High-end segment to refurbish and increase your engine compression!
Reference: 64432.00
A complete high-performance high-end engine special for SACHS 503 and 504 with a 14mm axle with 2 transfers with a long stroke crankshaft.
Reference: 148.6002
The POLINI 6000 series kit reproduced for enthusiasts! For 44mm stroke. Have
Reference: 85206.00
The piston-cylinder without cylinder head 70cc for ZUNDAPP air cooling as the CS50, KS50 ...
Reference: 42115.00
Very torquey, robust and powerful kit for KREIDLER FLORET HP 4,8.
Reference: 85438.00
A 70cc kit for ZUNDAPP air cooling for miniterm engines.
Reference: 020000/1
The ATHENA cylinder, piston, cylinder head, Ø48mm kit for SACHS CORSA LUNGA 50.
Reference: 020306435
Very good little aluminum kit for MORINI M1 engine, M101, M1ES, M1K ... 50 2T!
Reference: 64165.00
A high-performance and full high special range for motor SACHS 503 and 504 in axis of 12 with 4 transfers with a long stroke crankshaft.
Reference: 073600
80cc kit with inclined admission, more practical for certain carburetion assemblies!
Reference: 53498.00
The very last parmakit for 42mm stroke on MINARELLI P6 engine.
Reference: 85207.00
The complete kit 70cc for ZUNDAPP with its cylinder head!
Reference: 30132.00
Kit very torquey, robust and powerful for GUZZI DINGO SPORT 50cc 2T.
Reference: 85465.00
kit Ø45mm 70cc for ZUNDAP 50 air cooling, admission without valves on cylinder.
Reference: 003800
80cc kit of very high quality, complete with valves and pipe for motorization MORINI era!
Reference: 021700
The cylinder kit, piston, cylinder head, Ø48mm ATHENA for P4R, MACAL, MALAGUTI FIFTY ....
Reference: 020000
The ATHENA cylinder, piston, cylinder head, Ø48mm kit for SACHS CORSA LUNGA 50.