Reference: 1773
Adjustable REPLAY intake pipe for 17.5 to 21mm carburetor (Ø24mm fixing) for MINARELLI AM6 engine
A quality 360 ° swivel pipe to replace the old one Supplied with two 30 and 45 ° sleeves!
Banner
Here is the intake pipe for carburetors from Ø26 to 28mm on mécaboite Minarelli AM6 from BARIKIT. It is actually manufactured by RQ. This model is a flexible adjustable model. It is very sold and used! We will recommend it on an OKO type carburation ... A user, connoisseur and experienced will not be satisfied with a pipe like this but preferred MALOSSI, TPR, POLINI ... for example, MALOSSI, POLINI, TPR ... are studied, absorb vibrations, are aligned, short and well defined.
We will regret on this pipe a mediocre finish as well as a design not studied enough… On the one hand by the finish of the base is not at the top, this base comes out in round Ø27mm ... No valves have an entry of round diffuser! The sleeve is not aligned with the base and it is Ø28mm, the finish of the sleeve is worse than the base and the latter is made of sincerely low-end rubber. An oil intake is present (surprising for a pseudo competition pipe).
In addition, the sleeve systems against the aluminum base are totally outdated! Let’s be clear, we don’t really like to sell this type of equipment, but many of you have asked for it. We therefore offer it to you. The price is quite low, this intake pipe will therefore go very well for small low-end carburetors like Oko for example.
-For carburetor from Ø26 to 28mm
- 360 ° swiveling system
- Carburetor fixing diameter: for fixing diameter from Ø30 to 34mm
-Internal output diameter 27mm
-Internal 28mm input diameter (may vary…)
Reference: 1773
A quality 360 ° swivel pipe to replace the old one Supplied with two 30 and 45 ° sleeves!
Reference: 512119
A very well designed intake pipe, ideal to accompany a high engine configuration.
Reference: LC.44.400
The must of the admission kits for large configuration with carburetor in 28 to 35mm. Reserved for connoisseurs! Hyper short, super diffusion, carburetor up to 35mm, vibration scrub ... Simply the best.
Reference: 317.0005
Set of 2 M6 studs that can be used for many applications.
Reference: 53405.05
Pipe of admission ideal to accompany a carburetor 17.5mm to 21mm!
Reference: 215.0439
Special intake pipe for POLINI CP 23 and 24mm carburetors. 360 ° swivel with 40 ° tilt angle.
Reference: CL01
A competition model that will allow you to greatly improve the performance of your AM6.
Reference: 9906940
Ideal to accompany the carburetors 19 to 21mm on your mécaboite minarelli am6.
Reference: 2013801
A very high-end special for large carburations on MINARELLI AM6, DERBI ...
Reference: 487209
A good quality pipe with an almost perfect finish for a price more than affordable!
Reference: 9919270
Pipe replacement inlet diameter 24mm carburettor MIKUNI TM24 or other flexible mount models.
Reference: CT00746
A good quality pipe with an almost perfect finish for a more than affordable price!
Reference: 0211199B
21mm pipe for HONDA MB, MT, MTX 50 / MINARELLI AM6 50 ...
Reference: 467798
A good quality pipe with a near perfect finish for an affordable price.
Reference: 215.0397
Pipe of admission Ø19mm, ideal for laying a rigid 21mm PHBG 17.5 has a motorcycle that requires a bent pipe as the Aprilia RX, MX 50 ...
Reference: 467799
The unbeatable quality / price / practicality ratio for your am6 engines!