Reference: 247766
Inlet valves DOPPLER ER2 fiberglass for casings origin peugeot 103
Valves mounted in mono-lamelle fiberglass for your 103.
Banner
Ideal for mounting your flexible carburettors from 15 to 21mm PHBG or CP, this intake pipe is the most efficient on the market for Peugeot 103, it is extremely short and well venturized / studied.
Made in 3D printing by powder sintering. This process makes it possible to offer an optimum shape of the intake ducts.
Inventory of the different parts:
- 1 pipe
- 4 screws (number identical to the fixing point)
- 4 washers (number identical to the fixing point)
-1 sleeve
WARNING: the material used is sensitive to tightening, it is imperative not to exceed the tightening torque (4Nm), and not to forget to use the washers provided. In the case of incomplete sealing, favor the use of the joint bracket, rather than excessive tightening of the screws which would cause deformation of the sole.
Assembly :
1) Coat the contact surface of the joint surface of the CAF type joint bracket
2) Place the washers and screws provided, then screw until contact.
3) Tighten the screws to 4Nm
Reference: 247766
Valves mounted in mono-lamelle fiberglass for your 103.
Reference: 365117
Valves mounted in mono-slat carbon 0.35mm for your 103!
Reference: 293370
A quality sleeve that absorbs vibrations very well for better gas flow.
Reference: 1402
An intake pipe with a good finish that will allow you to mount your carburetor Ø14 to 16mm while gaining power.
Reference: 02 6487B
The best to accompany a 15 or 16mm SHA carburetor on your 103!
Reference: 02 5035B
The best to repair or modify the size of your MALOSSI valve boxes on your PEUGEOT 103 or MBK 51.
Reference: 928.270.006
POLINI pipe for THOR engine or adaptation on PEUGEOT 103 / MBK 51 requiring an elbow admission!
Reference: 02 6489B
A pipe specially designed for flexible assemblies. This pipe was specially created for the competition. It is therefore mounted with a flexible PHBG carburetor from 15 to 21mm.
Reference: 02 2083B
The top of the intake pipe to put your PHBG 17.5mm to 21mm on your 103.
Reference: 365641
A shorter pipe for better venturi effect. This pipe is the highest end of the market. It will be perfect with a carburetor 19 to 21mm.
Reference: 144.270.001
Flexible polini pipe 21mm for mini-moto and cross 2T POLINI, or mounting on POLINI crankcases with PEUGEOT 103 and MBK 51 supports!
Reference: 56251.05
Ideal with a carburettor PHBG 19 to 24mm and achieve maximum performance! Model "finned" for mob Peugeot 103 SPX, RCX ...
Reference: 1400
An amazing pipe with a very good finish that will agree very well with a carburetor 18 to 21mm.
Reference: 1314916B
Ø32mm spare sleeve angled at 90 ° internal for MALOSSI admission kit on VESPA 80, 125, 200 ...
Reference: 215.0227
High quality intake pipe for mounting PHBG carburetors from 17.5 to 21mm.
Reference: 496075
Ideal in case of breakage or wear your old room.
Reference: 1403
A pipe which will be perfect accompanied by a carburettor PHBG 19 to 21mm. This pipe is blasted with a good finish to avoid the rebound of gases.
Reference: 215.0370
Intake pipe for POLINI support housings incorporated on PEUGEOT 103.