Reference: 206.0202
Chrome steel segment Ø60X1mm for POLINI 154cc kit on ROTAX 122, 123, APRILIA RS, RX, SX, RED ROSE, HM ...
The segment for the POLINI 154cc kit on ROTAX 122 and 123!
Banner
Already well known for years, we offer the cylinder / piston / cylinder kit complete POLINI motori 154cc for motor ROTAX 127, the engine that equips 125cc 2 strokes like APRILIA CLASSIC, AF1, FUTURA, TUAREG, ETX 125cc, RED ROSE 125cc and other models .
The kit is announced by POLINI has a power of 29cv at 10 000rpm. The couple will also be greatly increased! The machine will be more flexible and the power more exploitable. Attention road use is forbidden. This piece is reserved for the circuit.
To increase the power, POLINI worked on the diameter of the piston (by simple increase), but also on the diagrams, the forms of lights, POLINI also re-examined the system of sweeping.
We recommend it with a relaxing exhaust, unbridled ignition, a minimum carburation of 30mm (round plug will suit wonderfully).
If your engine is very thorough, prepared, or even old, we will recommend to change the crankshaft, by the way do not hesitate to put a kit reinforced rod. A set of rigid plates of carbon valves will be the welcome in order to exploit the good schemes.
The pack contains :
Pack complete seal (with 3 base seals to make the squish)
Cylinder Ø60mm aluminum nykasil exhaust a boosters
Piston Ø60mm bi segment high silicon content
Set of 2 chrome-plated steel segments pre-ground
Piston shaft
Piston clips
Screws
Needle cage
Notice in French
...
As an option we offer a stage 1 preparation, this preparation is a modification of the channels and the exhaust light by increasing the diagrams and improving the duct, it increases the performance of the cylinder. An improvement of the piston and skirt stockings is also included in this modification. Allow a little extra time for this preparation!
Reference: 206.0202
The segment for the POLINI 154cc kit on ROTAX 122 and 123!
Reference: 272.0003
The G POLINI piston clips for your 15mm axle!
Reference: 209.0320
Ideal for maintaining your 154cc kit on your ROTAX 127 engine.
Reference: 271.0005
POLINI reinforced piston pin, ideal in case of loss of the old piston pin!
Reference: 204.0295/B
The complete replacement piston for the kit 154cc POLINI!
Reference: CK.01.140.G
Optimized version at 140cc for your 125cc motorcycle 2-stroke rotax 122 engine! High-end aluminum cylinder, 57mm diameter single-segment piston with intake transfers revised upwards, large diameter valve exhaust ... Supplied with stud cylinder head!
Reference: 065300
Exhaust huge, huge piston, compression ratio and excellent diagrams ... What impress a lot of people with your NSR 125cc! Out of production!
Reference: CI.01.126.G
An ideal solution to boost the performance of your 125cc motor rotax 123 2-stroke engine! High-end aluminum cylinder, piston diameter 54mm two-segment with studied intake transfers and valve exhaust ...
Reference: CI.01.127.G
A radical solution to improve the performance of your motorcycle 125cc rotax 122 2 stroke engine! High quality aluminum cylinder, piston diameter 54mm mono-segments with studied transfer transfers and valve exhaust ...
Reference: P400485100017
The famous athena 125cc kit from ATHENA for Yamaha YZ 125 motorcycles from 2005 to 2018.
Reference: 30140.00
Kit for motorcycles GUZZI ZIGOLO 1950/1960 ... 125cc 2T.
Reference: P400485100019
Ideal to replace your original engine and get good performance!
Reference: P400485100010
The most powerful kit released for TDR, DT, DTRE, DTR, DERBI GPR ... 2 times! Excellent quality, delivered with its modified exhaust valve!
Reference: CI.01.128.G
A radical solution to improve the performance of your 125cc 2-stroke rotax 123 engine! High-end aluminum cylinder, 54mm diameter piston mono-segments with studied intake transfers and valve exhaust ...
Reference: 63160.00
Set of two cylinders right and left for RUMI 125cc 2T era! Delivered with their cylinder heads high compressions.
Reference: 63120.00dx
Complete right kit with cylinder head for your old RUMI Bi-cylinder 2T!
Reference: VE.01.125
No more valve problems! Pneumatic system valve, high performance and reliability for your ROTAX 122 and 123!
Reference: CI.01.125.G
A unique solution to literally optimize the performance of your motorcycle 125cc rotax 122 2-stroke engine! The ITALKIT Sport version, high-end aluminum cylinder, piston diameter 54mm two-segment with studied intake transfers and valve exhaust ...
Reference: 63110.00
Kit left complete without cylinder head for your old RUMI Bi-cylinder 2T!
Reference: CI.01.141.G
Improved version to your 140cc 125cc Rotax engine 123 2 times! Cylinder premium aluminum, 57mm diameter piston with inlet transfers revised upwards, exhaust valve at large diameter ...
Reference: CIL-1027-S
The famous BARIKIT 144cc for ROTAX 122 engines!