Reference: 01486_72
Main Jet For DELLORTO Carburetor Small Pitch 5mm Thread 8mm Length Genuine (INC Certified)
Certified DELLORTO INC! Choose real DELLORTO quality!
Banner
Here is a very high-end carburetor from DELLORTO, not very expensive and well suited to small or large configurations, this BD model PHBG has a cable choke and is mounted on a flexible pipe. Solid, practical and resistant, it is equipped with a cap under the aluminum tank which allows the nozzle to be changed without dismantling the tank!
It does not have separate lubrication so you will have to mix it yourself! It is flexible mounting. You can mount it on the 103, 51, scooter, am6 and DERBI with original pipe ...
If the air filter fixing is in threaded Ø32mm, you can therefore put the cones and airbox sleeve in Ø31 to 33mm. You can also use the tulip delivered with the carburetor which will allow you to pass the large diameter 40mm air filters and provide better ventilation.
Material type :
Primary jet dellorto 95 in small steps
Needle: type W06
Cutting bushel: 40 degree
Choke jet size 60
Idle jet size 50
Then AU type needle in size 262
The choke is cable and the carburetor is male.
Float 4 grams
External diameter pipe side: 25mm
External diameter filter side: 32mm threaded or 40mm non-threaded with the tulip
The low consumption, the little noise it causes, the power and recovery it offers have made the reputation of the Italian DELL'ORTO carburettors. This SPECIAL version has a "screw-on" valve cover, this offers quick disassembly / reassembly, ideal for needle adjustments and cable changes! This is much more convenient than the 2 screw covers where it is often necessary to tilt / extend the carburetor.
Reference: 01486_72
Certified DELLORTO INC! Choose real DELLORTO quality!
Reference: 53024
The complete richness screw for your PHBG carburettors!
Reference: 09506
Bar, axle, float holding rod for DELLORTO carb.
Reference: 53027_00
The idle screw with its spring for your PHBG carburettors!
Reference: 09595_20
Needle, essential for adjustments or at the slightest wear, irregularity.
Reference: 09450
The replacement float for your carbs, ideal in the event of a fuel leak!
Reference: 09596_00
Ideal in case of loss or breakage.
Reference: 02838_00
Ideal in case of problem, breakage or loss of your old part!
Reference: 53002_00
A pack to switch your PHBG carburettors choke lever to cable choke!
Reference: 14958_00
Ideal in case of loss or breakage of your old support, bushel socket.
Reference: 52526_77
Ideal for refurbishing your standard PHBG or racing black edition.
Reference: 09597_00
The valve spring for your carbs, ideal when the handle returns badly or in the event of loss, wear, breakage...
Reference: 01488_30
Idle jet for PHBG and PHBD carburettors, to obtain a correct idle when the bushel is at the bottom! With a good reaction to the opening bushel!
Reference: 09654_264
Essential part for the proper functioning of your carburettor, ideal in case of wear or breakage...
Reference: 09501_40
Essential part for the proper functioning of your carburetor, several sizes to choose from to fine-tune your settings!
Reference: 09779_00
Essential part of your carburettor PHBG for better mixing oil / petrol! Not deep model for jet small step 5mm.
Reference: 09811_00
The aluminum racing tank, mounts on all PHBG carburettors, to remove your jets faster, drain faster and get more strength!
Reference: 01104_00
Arises directly in the plug cover, also available in angled with adjuster.
Reference: 2506
The AS 1 version of the real DELLORTO carburettor PHBG, rigid, choke lever without separate lubrication or depression.
Reference: 2575
An excellent version of the real PHBG RIGIDE DELLORTO 19mm, this CS has a large intake tulip, a lever choke and a possibility of separate lubrication!
Reference: 2522
The BS version on 19mm PHBG, flexible, lever choke! High quality certified!
Reference: 2523
The real DELLORTO PHBG in 18mm!
Reference: 2695
The most racing version of the carburettor DELLORTO RACING BLACK EDITION, flexible, choke cable, possibility of separate greasing.
Reference: 473460
A good quality carburetor for its price which will fuel your engine well but which will not have as good a finish as a DELLORTO.
Reference: 1179
The DD version on PHVB 19mm, flexible, cable starter! High quality certified!
Reference: 467793
A carburetor much better than a TNT but less well finished than a DELLORTO, but it will still provide a good filling of your engine for a relatively low price.
Reference: 201.1901
A very good high quality carburetor at a low price, with separate greasing and vacuum plugs! Choice of cable or lever choke!
Reference: 201.1902
A very good high quality carburetor at low price, with separate lubrication and vacuum plugs! Choice of cable or lever choke!
Reference: 201.1904
CP POLINI 19mm version in rigid mounting Indispensable for a prepared engine configuration.
Reference: 2577
The CS version of the DELLORTO PHBG Ø19.5mm. Excellent quality, with large diameter, rigid intake tulip, choke lever, with possibility of depression or separate lubrication!
Reference: 2568
The AS version of the DELLORTO PHBG Ø19,5mm. Excellent quality, with large diameter intake tulip, rigid, choke lever, without possibility of depression or separate greasing!
Reference: 201.1903
The best 19mm carburetor from POLINI and we can say about the whole market! An evolution version CP for maximum performance!
Reference: 466778
A carburetor that consumes little while fueling your engine well, and all at a low price!
Reference: 467791
Cheap and quality carburettor because it is located between TNT and DELLORTO.