Reference: 9929480
Set of 4 TOP PERFORMANCES M7 x 115mm studs for DERBI euro 3 & 4 high engine kit
High-end studs, of very good quality, ideal for replacing your old worn or broken ones.
Banner
MALOSSI adaptation part allowing the installation of a DERBI EURO 3 kit on a DERBI EURO 4 engine by adapting the temperature sensor.
Mounts on :
DERBI EURO 4 engine
APRILIA RS 50 2T LC euro 4 2018-> (D50B0)
APRILIA RX FACTORY 50 2T LC euro 4 2018-> (D50B0)
APRILIA SX 50 2T LC euro 4 2018-> (D50B0)
APRILIA SX FACTORY 50 2T LC euro 4 2018-> (D50B0)
DERBI Senda LIMITED SM 50 2T LC euro 4 2018-> (D50B0)
DERBI Senda X-TREME SM 50 2T LC euro 4 2018-> (D50B0)
GILERA DRIFTING 50 2T LC euro 4 2018-> (D50B0)
GILERA RCR 50 2T LC euro 4 2018-> (D50B0)
GILERA SMT 50 2T LC euro 4 2018-> (D50B0)
DERBI Senda X-TREME R 50 2T LC euro 4 2018-> (D50B0)
DERBI Senda RACING SM 50 2T LC euro 4 2018-> (D50B0)
Reference: 9929480
High-end studs, of very good quality, ideal for replacing your old worn or broken ones.
Reference: JAC-05
Ideal for raising your diagrams or for fitting a 43mm long stroke crankshaft on mécaboite DERBI euro 3 and 4 (Piaggio 2006 engine). Digitally machined aluminum shim.
Reference: 87181000
Ideal in case of breakage, loss or worn thread of your old nut.
Reference: 87171100
Ideal in case of breakage, loss or worn thread of your old nut.
Reference: 9928090
Ideal in case of wear of your old flange or even in case of breakage during the assembly of this one.
Reference: 11700118
2 pawns to improve your assembly of your kit, casing, cylinder head...
Reference: 483769
Well useful spare stones to continue using the lap TUN 'R for cylinder.
Reference: 19 6313Q
The strongest studs in the range, withstand extreme tightening torques. Amply support 25nm (2.25 mkg)!
Reference: ESP.07.116.4
The strongest with MALOSSI, support extreme tightening torques. Support ample 25nm (2,25 mkg)!
Reference: 1913105B
Ideal for refurbishment in case of breakage or wear.
Reference: X4 12512042
Reinforced and elongated nuts to better tighten the cylinder head and more precisely. They can withstand much higher tightening torques!
Reference: 167916
A set of reinforced and treated P2R cylinder head nuts for quality maintenance of your high engines.
Reference: 00002.87
Set of 4 M7 nuts with their 4 washers.
Reference: 317.0102
Quality stud and reinforced to prevent breakage or wear. Maximum tightening 18nm or 2,04mk / g. In addition to this, you need to know more about it.
Reference: S.1447 - 001447 (PIAGGIO)
Ideal in case of breakage, loss or worn thread of your old nut.
Reference: ESP.07.125.4
The strongest with MALOSSI, specially lengthened for high engines with wedges for stroke or long connecting rod, withstand extreme tightening torques. Amply support 25nm (2.25 mkg)!