 
	        
    Reference: 06040845
																					 
																		
Piston mono segment AIRSAL Ø45mm for kit 70cc HONDA MB, MT 50 ... air cooling
A good quality piston comes complete for refurbishment of your cylinder.
 PEUGEOT 103
PEUGEOT 103 MBK 51
MBK 51 MOTOBECANE
MOTOBECANE PIAGGIO CIAO / VELOFAX
PIAGGIO CIAO / VELOFAX PEUGEOT FOX
PEUGEOT FOX HONDA CAMINO, PX, PXR...
HONDA CAMINO, PX, PXR... DERBI VARIANT
DERBI VARIANT.png) SOLEX
SOLEX PUCH
PUCH MINARELLI AM6
MINARELLI AM6 Low-pass exhaust pipe
Low-pass exhaust pipe High-pass exhaust pipe
High-pass exhaust pipe DERBI Euro 3 / 4 / 5
DERBI Euro 3 / 4 / 5 DERBI Euro 1 & 2
DERBI Euro 1 & 2 MINARELLI P4 & P6
MINARELLI P4 & P6.png) MINARELLI RV6, RV5, RV4, RV3
MINARELLI RV6, RV5, RV4, RV3 SUZUKI SMX, RMX, TSX
SUZUKI SMX, RMX, TSX YAMAHA TY, RD, DT, MX
YAMAHA TY, RD, DT, MX HONDA MB, MT, MTX, MBX, NSR R
HONDA MB, MT, MTX, MBX, NSR R YAMAHA CHAPPY
YAMAHA CHAPPYBanner
 
				
				
					 
	         
          Warning, reserved for use on the circuit, modifies the original displacement.
 Between performance, strength and good price! This high 70cc engine kit in 45mm diameter from AIRSAL will be an excellent compromise for your motor bike HONDA MB 50, MT 50, MTX 50 .... 
 This cylinder is therefore in good quality aluminum with transfers and an exhaust reworked and revised upwards, the finish is good and clean, it will above all offer you the torque and the speed that the original engine cannot exploit. , in association with a prepared carburetion and a released exhaust. 
 The piston is a single segment model which will promote high speeds (reduced friction), it has a low domed cap in order to obtain more pre-compression. You can install the original cylinder head without problem, the best would be to plan it at a specialist in order to tune your cylinder / cylinder head to perfection. 
 This piston is equipped with two openings on the back to promote filling / sweeping at the level of your admission, its fixing center distance for the manifold / intake pipe is 61 X 40mm. Comes complete with seal pack, segment, clips, axle ... as presented. This set will be a real performance asset for your motorcycle, an excellent quality / price and performance ratio! 
We recommend accompanying this kit with at least : 24mm carburetion, cold racing spark plug, 100% synthetic racing engine oil, adapted exhaust to free up volumes and performance ....
Contains :
-Aluminum cylinder Ø45mm 70cc 6 transfers
 -Piston mono segment with rear opening, low domed cap
 -Standard cast iron segment Ø45mm X 1.5mm thick
-Reinforced G clips
-Piston axis Ø12mm X 36mm in length
-Pack high engine seal (cylinder head, cylinder, intake, pot)
 As an option we offer you a stage 1 preparation, this preparation is a modification of the channels and the exhaust port by increasing the diagrams and improving the duct, it increases the performance of the cylinder. An improvement to the piston and the bottom of the skirt is also included in this modification. Allow a little extra time for this preparation!
Reference: 06040845
																					 
																		
A good quality piston comes complete for refurbishment of your cylinder.
Reference: 14040845
																					 
																		
Ideal for refurbishment perfect and without leakage. Make sure you change your joints at each disassembly.
Reference: 31302.00
																					 
																		
A perfect high engine to boost your motorcycle as needed HONDA 50 MB, MB, MTX ...!
Reference: CIL-710
																					 
																		
A very torquey 70cc with a very low price for your old motorcycles 50cc HONDA!
Reference: 007500
																					 
																		
A 70cc kit with a super torque / power ratio and rock solid strength!
Reference: 31553.00
																					 
																		
A powerful kit for your HONDA MBX and NSR 80 motorcycle.
Reference: 31525.00
																					 
																		
A torquey kit solid that will get your 50cc motorcycle 70cc Spent a monster.
Reference: 02040845
																					 
																		
A high-performance kit at a good price!
Reference: 31610.00
																					 
																		
Large diameter kit for 50cc 4T HONDA engines from 1970/1980.
Reference: 31 4260
																					 
																		
A solid cast iron kit ideal for increasing your performance!
