Approved on the highway, complies with the 50cc regulatory cylinder capacity.
Here is an excellent high-performance 50cc aluminum kit for Minarelli AM6 engine mecaboite, this is the model AIRSAL XTREM Racing with a single segment piston with a bore diameter Ø40.30 mm. This aluminum model offers a 50cc power regulation cylinder capacity to be in order and circulate every day, solid thanks to the aluminium alloys used. With its inbound high-compression cap to optimize alignment with the cylinder and increase engine compression.
Its aluminium cylinder therefore has 5 intake transfers of which 1 has the rear and 4 side. Its intake is reworked, we also recommend to mount a PHBG 19mm carburettor on the cylinder see 21mm if you rework slightly the intake, the exhaust output is also significantly improved thanks to a booster output. Diameter of exhaust outlet Ø28 mm, hold for passage to diameter Ø25 mm not provided.
A very well studied architecture for this small aluminium thus offering performance, high speeds improved compared to the original model, especially coupled with the good compression ratio offered by the truncated combustion chamber, polished finish of the head. A screw and fitting kit is also provided, as presented in addition to the joint pack with two base joints of different thickness to refine your squish.
This kit does not neglect the torque but favours high engine efficiency, its strength is not altered with its resistant single-segment piston which fits perfectly with this cylinder it goes either, a fine chrome segment resistant favoring the rise in speed, thickness of the latter 1 mm.
For a very correct price, you will have a high engine that respects the 50cc cylinder capacity and offers well felt performance! An excellent base of preparation also for the most connoisseurs wishing to enjoy themselves every day or circulate on circuit. The cooling system is also improved thanks to the well-constructed head, in bie part by the same time and the aluminium alloys used.
We recommend that you accompany this high engine with at least: 19 mm carburation, flexible mounting pipe intake, crankshaft and reinforced bearings for the best and start again on a completely new and trouble-free engine, new racing candle, 100% synthetic engine oil, release exhaust... .
The pack contains:
-Aluminum cylinder Ø40.30 mm 5 transfers with bar
-High compression cup truncated chamber polished finish with inlet plot
-Piston 40.30 mm single segment
-1 Thin chrome segment thickness 1 mm
-Piston axis Ø12 X 33 mm
-Crab type piston clips
-Pack complete joint
-Body of the head
-Adhesive
Optionally we offer a stage 1 preparation, this preparation is a modification of the exhaust light by increasing the diagrams and improving the duct, it increases the performance of the cylinder. An improvement of skirt stockings is also included in this change. Count a little extra time for this preparation!
This high engine is mounted on the following 50cc motorcycles with gearbox equipped with MINARELLI AM3, AM4, AM5, AM6 euro 1, AM6 euro 2:
-APRILIA RS AM6 engine from 1997 to 2006 (after 2006, attention to engines passed DERBI euro (3)
-APRILIA RX AM6 engine (after 2006, attention to engines passed in DERBI euro (3)
-APRILIA MX AM6 engine (after 2006, attention to engines passed in DERBI euro (3)
-BETA CREE
-BETA RR
-BETA RR ALU
-HONDA HM
-HONDA CREE
-HONDA BAJA
-HUSQUVARNA WXE
-HUSQUVARNA CH
-HM DERAPAGE
-HM CRE
-MALAGUTI DRAKON
-MALAGUTI XTM
-MALAGUTI XSM
-FANTIC CABALLERO
-PEUGEOT XP6
-PEUGEOT XPS
-PEUGEOT XP STREET
-PEUGEOT XP STREET EVO
-PEUGEOT XR6
-PEUGEOT XR7
-MOTORHISPANIA RYZ
-MOTORHISPANIA RX-R
-MOTORHISPANIA RX
-RIJU RS1
-RIJU RS2
-RIJU RS2 MATRIX
-RIEJU RS2 MATRIX PRO
-RIEJU SMX
-RIEJU MRX
-RIEJU SPIKE
-KEEWAY TX EN
-YAMAHA DT
-MBK X-LIMIT
-YAMAHA TZR
-MBK X-POWER
-SHERCO SM
-SHERCO ENDURO
-SHERCO HRD
-SHERCO ENDURO
And many more machines!
.png)
.png)
