- There are no more items in your cart
- Shipping Free
- Total €0.00
Model with standard M8X1.25 nut for the crankshaft, also available in M10X1.25
Specific model for PIAGGIO CIAO SC and PX 50
No need to push or pedal to start!
If you convert your PIAGGIO moped to a pedal, for example, and forgo the pedal/chain start, you often have difficulty getting it started because, depending on the gear ratio, it is hardly possible to push. With the sophisticated MCSPK (MC Pullstart Kit), a sophisticated starter cable from MCPROPARTS, starting the moped like a chainsaw is no longer a problem.
What are the advantages of the jumper cable?
Slim and sophisticated design
Ready to install
With titanium starting nut
Slim, low profile design with recessed starter housing on a CNC machined base plate from 6062T6 aluminum and anodized black. The 3 studs are made of 1.4305 stainless steel and covered with a black PVD coating. Additionally, the studs feature a shoulder that grips the base plate and thus prevents twisting or incorrect assembly, while reducing the tipping moment by widening the screwing surface! Here too, great emphasis has been placed on a slim design, so that there is no need for the usual 15-18mm holes in the side parts. All visible parts of the frame, such as screws and washers, are made of stainless steel and coated with black BZP.
The highlight of the show
The included nut is CNC machined from grade 5 titanium (3.7164) and weighs 17g! Some of the usual nut sets on the market weigh over 100g or are made from aluminum! The titanium nut is not only indestructible and guarantees a very long thread life, but it also protects the crankshaft and bearing seats in the crankcase. If you care about your crankshaft and/or bearings, it is best not to install a drive nut weighing more than 30g due to the rotating mass and exposed mounting location at the end of the crankshaft. Particularly in the case of tuned and high-speed engines, this can quickly lead to damage!
The MCPROPARTS footrest kit is mandatory.
To fit the left side panel door, it must be machined. To avoid destroying the beautiful original side panel trim, we recommend using the inexpensive aftermarket side panel trim.
Reference: 171.0679
Balancing disc for POLINI ignition with original type hollow mass crankshaft
Balancing disc for electronic POLINI ignition on PIAGGIO CIAO.
Reference: 6616872E
Set of 2 reinforced crankshaft bearings MALOSSI C3 for PIAGGIO CIAO, PX / SOLEX
Set of two reinforced bearings C3 MALOSSI for CIAO, SOLEX ...
Reference: P400480444002
Crankshaft bearing kit + RMS oil seals for PIAGGIO CIAO
Set of bearings + spinnaker seals for PIAGGIO CIAO.
Reference: 280.0040
POLINI reinforced high speed crankshaft bearing C4 for PIAGGIO CIAO, PX / SOLEX
Reinforced bearing for low engine of CIAO, SOLEX ...
Reference: PI113681 / 113681 (PIAGGIO)
Washer between bearing and crankshaft Ø15 X 21mm thickness 5mm for PIAGGIO CIAO
Washer between bearing and crankshaft for PIAGGIO CIAO.
Reference: 285.0122
Crankshaft oil seal POLINI Motori reinforced 15X24x5mm type G for crankcase ORIGIN on PIAGGIO CIAO, PX
POLINI spy joint for crankcase ORIGIN on PIAGGIO CIAO.
Reference: C5182KT
Engine overhaul kit with bearings, key, washers, seals, spinnaker ... For PIAGGIO CIAO
Overhaul kit for a perfect reassembly!
Reference: 66 4678E
Set of 2 reinforced crankshaft bearings MALOSSI for PIAGGIO CIAO, PX / SOLEX
Set of two reinforced bearings MALOSSI for CIAO, SOLEX ...
Reference: C5185
Nut M8 X 1,25mm for variator, clutch from PIAGGIO CIAO
Nut for 13mm spanner, on PIAGGIO CIAO crankshafts.
Reference: R121858530
Veiled washer for ignition flywheel on crankshaft for PIAGGIO CIAO
Washer for ignition rotor for PIAGGIO CIAO.
Reference: MCABC001
Set of reinforced brass MC PROPARTS bottom bracket rings for PIAGGIO CIAO
Reinforced bottom bracket ring for CIAO.
Reference: 135253
Bushing, saddle bush / rear swingarm ORIGINAL for PIAGGIO CIAO
Rear saddle/swingarm bushing
Reference: 66 4168.J0
crankshaft oil seal 15x24 MALOSSI reinforced for PIAGGIO CIAO
Joint spy MALOSSI for PIAGGIO CIAO.
Reference: MCPSKM8
MC PROPARTS pull starter kit for PIAGGIO CIAO with standard M8X1.25 crankshaft nut
Reinforced rear arm ring, luggage rack or saddle for CIAO.
Reference: 3268
TEKNIX reinforced crankshaft spy seal for PIAGGIO CIAO, PX
Ideal for refurbishment with good quality products at low prices.