Reference: 140.0133
Kit 65cc Ø43mm with cylinder head (axis Ø10 / 12mm) POLINI Motori cast PIAGGIO Ciao, bravo, boss, grillo, if, superbravo ...
A kit very well finished this kit allows a maximum of torque and solidity out of norm.
Banner
If you are looking for a solid and efficient kit for your CIAO, then this set is for you! POLINI struck very hard by finally getting rid of the known defects of the PIAGGIO CIAO on a large cast iron cylinder!
1- Polini switches to a 4-stud system for greater robustness and more freedom in terms of ducts (which requires you to use POLINI 170.0201 casings
2- Polini uses a large diameter interchangeable exhaust ball joint that is well released: one in 22.3 diameter and one in 27mm diameter (we are talking about external diameters)!
3- Polini uses big lateral transfers as well as a monstrous bar exhaust!
Let's make things clear right away, there is no need to fit this kit with a 13mm SHA carburetor and an original type exhaust... You must absolutely adopt a POLINI crankcase with RACE type valves, but also a 19mm PHBG carburettor, a racing exhaust ideally 27mm in diameter, as well as good electronic ignition and a reinforced crankshaft with 12mm axle!
The result is breathtaking, especially with a variator engine (not a single clutch), you will obtain excellent acceleration, arm-twisting acceleration and high top speeds on your favorite circuits! It goes without saying that a chassis of the height must accompany the beast!
Mounts on :
PIAGGIO BRAVO 50
PIAGGIO BOSS 50
PIAGGIO GRILLO 50
PIAGGIO SI 50
PIAGGIO SUPERBRAVO 50
PIAGGIO CBA 50
and other models.
As an option we offer a stage 1 preparation, this preparation is a modification of the exhaust port by increasing the diagrams and improving the duct, it increases the performance of the cylinder. An improvement to the bottom of the skirt is also included in this modification. Allow a little extra time for this preparation!
Reference: 140.0133
A kit very well finished this kit allows a maximum of torque and solidity out of norm.
Reference: 3118050 / 3118052
The must of 70cc kit for PIAGGIO Ciao. A real performance monster with 6 intake transfers, large bar exhaust, high compression cylinder head ... An exceptional high engine for guaranteed performance !!!
Reference: 5007
Cylinder without solid and powerful ass for your moped PIAGGIO CIAO. Available in 10mm axis only.
Reference: 061300
A very clean and well finished cast iron kit that will bring you considerable power gain without denigrating the reliability of your PIAGGIO.
Reference: 116.0145
An excellent very torquey and robust kit for your old PIAGGIO VESPINO, VELOFAX and your GILERA VALE, TOLEDA, GSA, ALX!
Reference: KT00067
A high quality engine with nice performance!
Reference: 3118567
The famous MALOSSI CVF available in 10 and 12mm axle with its radial head for CIAO.
Reference: 3118709
The CVF piston cylinder 65cc 43mm for PIAGGIO CIAO without cylinder head!
Reference: 48103.00
A high quality and resistant engine! The most powerful kit on the market for VELOFAX PIAGGIO type engine!
Reference: 020609435
A high quality and resistant engine! Model without cylinder head.
Reference: 140.0065/10ST
The famous POLINI 43mm for piaggio ciao cast iron without cylinder head.
Reference: 065500
A very clean and efficient kit, in aluminum which will bring you a considerable gain in power without neglecting the reliability of your CIAO. In addition to this, you need to know more about it.
Reference: 064900
One of the only aluminum kit that will bring you considerable power gain without denigrating the reliability of your PIAGGIO.
Reference: 140.0133/10R
Following many requests, POLINI finally comes out! The version FONTE RACING for ciao !!!
Reference: 31 6158 / 3118570
A high solid and powerful engine to improve the performance of your Piaggio moped.
Reference: 57240.00
Cylinder head without strong and efficient for your moped PIAGGIO CIAO. Available in 10 or 12mm axle choices.