Reference: 009512
ATHENA Racing competition valves minarelli am6
High quality competition valves, bonded aluminum base!
Banner
High quality 80cc ATHENA kit. Ø 48mm big bore, it consists of a high-end nicasil treated aluminum cylinder from EUROCILINDRO.
From an ASSO piston with high silicon content, flat cap with single L-segment.
This excellent set is given with a valve box adhered to the viton with two double slats joined in karbonit fiber, you can mount them with or without slat stops.
Intake plates, muffler ball joint ...
This complete high performance set is obviously very torquey and robust, ideal for refurbishing your old MORINI 2T 50.
As an option we offer you a stage 1 preparation, this preparation is a modification of the channels and the exhaust port by increasing the diagrams and improving the duct, it increases the performance of the cylinder. An improvement to the piston and the bottom of the skirt is also included in this modification. Allow a little extra time for this preparation!
Mounts on old MORINI engines :
Franco Morini 2T G30 - Motorcycles-mopeds
MORINI S5 / GS
KTM SX 50
Malaguti FIFTY FULL CX 50 - 1991/1991 - Motorcycles-mopeds
Moto Gac WINNER 50 - Motorcycles-mopeds
LEM 50
Reference: 009512
High quality competition valves, bonded aluminum base!
Reference: S410000304002
The ATHENA clips of good quality for 12mm axles with 1mm diameter piston groove!
Reference: 001716/R
High-end segment to refurbish and increase your engine compression.
Reference: 021725
The flange has 2 screws for fixing the muffler in Ø29mm ATHENA for P4, P6 ...
Reference: 003803
Pack of complete seal for kit 80cc ATHENA air on MORINI T4, GS, TUNTURI, ZENELLA, PERIPOLI ...
Reference: 85465.00
kit Ø45mm 70cc for ZUNDAP 50 air cooling, admission without valves on cylinder.
Reference: 64168.00
A high-performance and full high special range for motor SACHS 503 and 504 in axis of 14mm with 4 transfers with a long-stroke crankshaft.
Reference: 64430.00
A high-performance and full high special range for motor SACHS 503 and 504 in axis of 12mm with 2 transfers with a long stroke crankshaft.
Reference: 53490.00
A high-performance top special range 42mm stroke motor Minarelli P6! Exhaust mounting by 3 screws for RADIAL SYSTEM.
Reference: 073800
The most powerful kit on the market for SACHS has cylinder head connected to the cylinder! Full version with clamshells!
Reference: 26105.00
Very torquey, robust and powerful kit for FLANDRIA 50cc 2T.
Reference: 42115.00
Very torquey, robust and powerful kit for KREIDLER FLORET HP 4,8.
Reference: 012002435
A complete set of quality. Guaranteed performance!
Reference: 64266.00
A high-performance high-end special engine for SACHS 503 and 504 in axis of 12mm with 4 transfers with a long stroke crankshaft.
Reference: 148.6008
The POLINI 6000 series kit reproduced for enthusiasts! For 39.6mm stroke.
Reference: 64445.00
A high-performance and full high special range for motor SACHS 503 and 504 in axis of 12mm with 4 transfers with a short stroke crankshaft.
Reference: 25104.00
PARMAKIT 80cc special kit for old FANTIC CABALLERO. 48X48mm studs.
Reference: 64425.00
A high-performance high-end special engine for SACHS 503 and 504 in axis of 12mm with 2 transfers with a long stroke crankshaft.
Reference: 85211.00.pr.st.1
The high engine without cylinder head, 70cc, for ZUNDAPP air cooling, big model with flaps!
Reference: 074000/1
Very good 70cc kit for SACHS integrated cylinder head! Available with or without intake pipe.
Reference: 85438.00
A 70cc kit for ZUNDAPP air cooling for miniterm engines.