Reference: 6611785B
Needle cage reinforced MALOSSI Ø12X17X16mm minarelli am6, DERBI, PIAGGIO, scooters ...
High quality needle cage, reinforced! ideal on the most advanced configurations.
Banner
Unapproved, banned on public roads for competition and closed circuits!
This high engine 70cc MALOSSI MHR TEAM is a concentrated authentic performance thanks to its design, study, architecture and elements that accompanies it. Its aluminum cylinder nikasil treated with specific heat treatment, has excellent finishes and has 7 large intake transfers extensively revised upwards with a massive exhaust with bar.
The piston is a model mono segment Ø47,6mm diameter promoting high speeds (reducing friction), equipped with its end segment chrome domed honed, clips reinforced C and its axis 12mm. Also (piston) was created from the finest materials to ensure good heat resistance and temperature changes with an outer coating of graphite to an even lower coefficient of friction.
Finally, a high-end stud bolt which will ensure maximum reliability, optimization of cooling .... Aluminum, it attaches directly to the cylinder for better heat exchange. Its combustion chamber is a high compression with extreme finish.
. Delivered 100% complete as shown Machining housings will be essential for the passage of a cylinder with only MALOSSI crankshaft (refs 53 8009 - 5,314,548 to 5,312,810). With gasket set for the squish, studs, accessories, hardware ....
We recommend to accompany this high engine with at least: minimum Ø21mm carburizing, an intake kit, racing exhaust, ultra reinforced vilbebrequin (brand MALOSSI required to mount it), reinforced bearings, cold candle racing, oil 100% synthetic motor racing, a large variation range, a racing ignition, careful monitoring and running, mounting in the rules ....
Optional we offer a preparation course 1, this preparation is a modification of the exhaust port by increasing the charts and improvement of the duct, it increases the cylinder performance. Improved bottom skirt is also included in the amendment. Allow a little extra time for this preparation!
Itself on:
Engine 2 Time minarelli horizontal liquid scooter
2 motor scooter minarelli horizontal air Time Spent liquid (long only)
APRILIA AREA 51 LC
APRILIA GULLIVER 50
Aprilia SR 50 LC NETSCAPER
APRILIA RALLY 50 LC
RACING APRILIA SR 50 LC
APRILIA SONIC LC
APRILIA SR REPLICA LC
APRILIA SR STEALTH
BENELLI 491 SPORT LC
BENELLI K2 50 LC
BETA ARK 50 LC
BETA EIKON 50 LC
GSP GARELLI 50 LC
ITALJET DREAGSTER 50 LC
MALAGUTI F15 FIREFOX 50 LC
MALAGUTI F12 DIGIT KAT LC
MALAGUTI F12 LC Phatom
MALAGUTI F12 R LC
MBK MACH G 50 LC
MBK NITRO 50 LC
YAMAHA AEROX 50 LC
YAMAHA JogRR 50 LC
Reference: 6611785B
High quality needle cage, reinforced! ideal on the most advanced configurations.
Reference: 36 4450
Do not forget to change at each winding to prevent engine failure thereafter.
Reference: 38 9513
For stud head only, covers aluminum cylinder head essential to replace your old piece out of use.
Reference: 1113209B
A seal pack upscale, essential for a safe winding and leakage.
Reference: 19 9419Q
Ideal for replacing your old bolts MALOSSI MHR.
Reference: 34 8654.A0
A spare piston high-end treatment with graphite, several sizes available!
Reference: 27 8359B
Essential for the refurbishment of your cooling system.
Reference: 3513982B
Ideal for refurbishing your high engine.
Reference: 2312580
Reinforced MALOSSI piston pin, ideal for the loss of the old piston pin!
Reference: 38 9512
A replacement stud with a high compression chamber of very good quality.
Reference: 3112641
A cylinder / piston without cylinder head high performance thanks to its increased displacement and 7 large intake transfers.
Reference: 3113036
The original must race kit market. Out of production!
Reference: 010726476
A very good price / quality, performance and torque! Luxury model.
Reference: 3112642.T0
Kit MALOSSI MHR TEAM 2 Factory Ø47.6mm axis Ø13mm for minarelli horizontal liquid (nitro, aerox, ...)
Reference: 31 8460
For more performance and a strong engine! This 70cc will be very good to equip your scooter with low Minarelli / Yamaha engine horizontal.
Reference: 3115901
Maximum performance, only for liquid-cooled scooters (7 transfers and exhaust bar - single segment piston - decomposable cylinder head!
Reference: 010735476
An ultra high motor racing, high performance while it has reasonable price.
Reference: H01073947
A kit much stronger than the aluminum AIRSAL and very torquey. A perfect kit to ride every day and over long distance without fear of a heater or primer.
Reference: 01073450
A high ultra racing engine, very powerful all this at a price never seen for such quality.
Reference: EQ-754
High performance version from BARIKIT in 10 transfers!
Reference: 010713476
The cheapest aluminum cylinders, made in spain, AIRSAL is good and offers good performance at a reduced price.
Reference: 3115390
Replacing the famous MALOSSI MHR TEAM!
Reference: EQ-995-S
The famous 47mm (70cc) aluminum BARIKIT Racing! A powerful cylinder accompanied by a good engine configuration. 50cc motorcycle engine with liquid scooter minarelli (nitro, aerox ...).
Reference: KT00109
A kit that offers torque, speed but also a lot of solidity!
Reference: 072400
A wonderful kit that announces high performance while maintaining high strength.
Reference: 31 8430
A very good compromise between strength and power!
Reference: 3113262
A very good compromise between strength and power!