Reference: 213.0012
POLINI competition valves for scooter VESPA ET3, ETS, SPECIAL ... PIAGGIO APE 50, 125cc
High-end valves complete with slats. To be assembled in the pipes admission kits with POLINI valves from VESPA, APE ...
Banner
With a lot of study and conceived in the best materials, here is the system monolamelle on the intake manifold Ø19mm 2 holes of fixing POLINI for scooter VESPA. Of course of high quality, it removes all the disadvantages of the original admission. Go from a standard system to a valve system and gain torque, power, consumption ... It can land with original crankcase and crankshaft with a carburization of 19mm POLINI CP reference 201.1905 or 21mm 201.2103 . For more power, POLINI recommends crankcase preparation. Comes complete as presented.
In download link, a PDF 100% complete technical diagram and advises use of this admission.
Mounts on:
-VESPA: VESPA 50 PK - VESPA 50 XL - VESPA 125 PK - VESPA 125 XL ...
POLINI strongly advises after 200 km of use to carry out a serious and general control of the assembly of this admission. To check the tightening and locking against the housing. All this due to the increase in power caused by this piece of competition.
Reference: 213.0012
High-end valves complete with slats. To be assembled in the pipes admission kits with POLINI valves from VESPA, APE ...
Reference: 201.1905
A carburetor pre-set and delivered ready to be mounted on your original vespa 50 and 125 pipe.
Reference: 201.2103
A pre-adjusted carburetor delivered ready to be fitted to your original vespa 50 and 125 pipe.
Reference: 11251700
Replacement aluminum intake sleeve for your VESPA!
Reference: 215.0230
Unique and efficient design, POLINI single-leaf system for VESPA scooter, Ø24mm 3 fixing holes.
Reference: 20 4709
Inlet pipe for MALOSSI carburettors or other soft mountings on your VESPA scooter.
Reference: 215.0232
Ideal to pass on a system has flaps and thus to gain in couple, power and consomation! To accompany a 17,5mm POLINI CP special for the best!
Reference: 215.0118
Valve system with flexible sleeve for increased power and torque!
Reference: 215.0272
The best way to mount a big PWK carburetor on your PIAGGIO APE by gaining performance!
Reference: 02 5084B
Ideal for improving and optimizing the performance of your PIAGGIO APE scooter.
Reference: 215.0205
For improved intake (to pass over valve system) with carburettor POLINI CP or other flexible mounting in Ø22 to 26mm, fixing by 2 holes as the origin.
Reference: 215.0115
Inlet kit with single-flap valves! Gain of torque and very high power in relation to a mounting without valves.
Reference: 215.0231
Unique and efficient design, POLINI mono-lamella system for VESPA scooter in diameter 19mm for POLINI or original carburetor with 3 fixing holes.
Reference: 215.0233
For an improved admission with carburettor POLINI CP 24mm, fixing by 3 holes! High performances guaranteed!
Reference: 215.0006
Intake pipe for POLINI CP carburettors or other flexible assemblies.
Reference: 215.0005
Black painted steel pipe for 16/16 carburettors on VESPA 50 SPECIAL 2T.
Reference: 215.0162
Ideal for improving and optimizing the performance of your VESPA scooter.
Reference: 215.0113
Valve inlet pipe for special kit POLINI 140.0051 / L.
Reference: 20 5461
The best way to mount a large PHBL carburetor on your VESPA ETS and PK 50 or 125cc and increase your performance!