Reference: S410000200004
Air filter, foam cone ATHENA with right cover 0 ° Ø35 and 49mm
A very high quality air filter that will filter all impurities without disturbing the engine performance.
Banner
Ultralight machined aluminum horn, for threaded carburetors, available in 16 sizes shown below. Without even a protective grid at the entrance, it is therefore recommended only on a clean track.
This filter increases the performance by improving the venturi effect, however the noise developed serras increased and more castling.
Available sizes (Ø = fixing Ø and L = horn length) :
Ø32X L 33mm (DELLORTO PHBG threaded)
Ø32X L 64mm (DELLORTO PHBG threaded)
Ø35X L 36mm (MIKUNI)
Ø35X L 60mm (MIKUNI)
Ø38X L 25mm
Ø38X L 70mm
Ø39X L 70mm
Ø40X L 42mm (threaded DELLORTO PHBH, non-threaded PHBL, MIKUNI ...)
Ø42X L 40mm (DELLORTO PHBH unthreaded)
Ø42 XL 58mm (without grid and without thread)
Ø42X L 65mm (DELLORTO PHBH unthreaded)
Ø43X L 33mm (MIKUNI, without grid)
Ø48X L 20mm
Ø48X L 36mm
Ø48X L 57mm
Ø48X L 61mm
Ø50X L 61mm (DELLORTO VHST, KEIHIN PWK, MIKUNI ...)
Ø59X L 37mm (DELLORTO SHA)
Ø55X L 63mm (MIKUNI)
The information next to the sizes is only indicative, you must take the Ø of your carburetor at the level of the air filter attachment !!! You should know that an unthreaded Ø 32mm horn will be mounted on a carburetor with a fixing Ø of 31.50 to 32.50mm. A Ø52mm horn will be mounted on a carburetor with a fixing Ø of 54 to 56mm without problems!
Reference: S410000200004
A very high quality air filter that will filter all impurities without disturbing the engine performance.
Reference: S410000200009
A competition filter with expanded foam that allows a large volume of air and therefore better recovery and performance.
Reference: 203.0062
Ideal for positioning your filter at 30 °, a high-end filter for optimal protection of your engine against external impurities.
Reference: 492195
TEKNIX foam air filter for motorcycle BETA RR 50 from 2005 (SM, EN DURO , ...)
Reference: 04 3072
Here is a small filter that allows you to have a lot of area while taking up little space.
Reference: 04 1418
A small filter that takes up little space but allows good filtration and a good supply of air.
Reference: 203.1504
A machined / blue anodized part POLINI for your PHBG carburettors!
Reference: 482106
A quality filter original type, single layer of black foam.
Reference: 203.1505
Ideal to fit your Ø70mm air filter on your PWK carburetor.
Reference: 928.465.004
Ideal for modifying, increasing or reducing your air intake on the POLINI large volume gearbox!
Reference: 114005
Ideal to repair and maintain the air box on your CPI SM, SX ....
Reference: 203.0150
A filter with a big reserve of air, special big PWK carburetor and other models. Ideal for a motor prepared competition!
Reference: 09814_00
A tulip which increases the venturi effect and therefore the efficiency of your engine. In addition to this, you need to know more about it.
Reference: 466739
A design air filter worked with very good performance.
Reference: 203.0147
An air filter with a large reserve of air for optimal breathing of your engine!
Reference: S410000200011
A competition filter with expanded foam that allows a large volume of air and therefore better recovery and performance.