Reference: 3812387
Ø50mm cylinder head stud for 80cc MALOSSI MHR TEAM kit on minarelli am6 and DERBI euro 3 & 4
A replacement stud with a high compression chamber of very good quality.
Banner
MHR automatically inspires quality and maximum performance! It is a mark of the MALOSSI Italian.
MHR MALOSSI HYPER RACING mean, it's a brand of Italian MALOSSI represents the elite of the range! The MHR products are the most advanced, the best but obviously more expensive. The range is wide enough especially for the scooter, there are ultra durable and well-balanced crankshaft, top 50 and 70 engines 80cc or even high quality worked to specific cooling, with treatments on top. Large inverters beaches, ultra performance exhausts with silencers that are almost art work (cast end caps, machined tube mass ....). By choosing MHR ... It is sure to get the desired performance and quality.
MALOSSI society today:
Malossi spa leadership in the production of special racing parts for scooters and motorcycles has its bases on different reasons: the experience that comes from 70 years of uninterrupted activity, the great passion for motorcycles that brings three generation of this family and finally one absolute imperative: quality and technology before everything!
The motto of this company is summed up in few words: always better!
The Malossi strong point is to be able to hold without calling out a complete production cycle, from research and project to the construction of molds and work with robots to arrive for testing in test facilities, test benches and chemical laboratories and metrology.
Website
There are 448 products.
Reference: 3812387
A replacement stud with a high compression chamber of very good quality.
Reference: 3411346.A0
Spare piston mono-segment for MHR Alu 70cc on minarelli scooter engine / vertical air yamaha.
Reference: 38 8186
Spare cylinder head MALOSSI MHR for Replica 70cc in diameter 47mm.
Reference: 3812773
Cylinder replacement MALOSSI MHR for 70cc in diameter 47mm aluminum.
Reference: 38 8578
Spare cylinder head MALOSSI MHR for kit 50cc in diameter 40mm Replica.
Reference: 3812382
A replacement stud with a high compression chamber of very good quality.
Reference: 3513536B
Chromed / pre-ground KDNS steel segment for MALOSSI MHR TEAM and REPLICA 50cc on am6, also available in cheaper cast steel!
Reference: 5512787
Spare parts ideal in case of failure, wear, breakage ... on your ignition by MALOSSI SELETTRA.
Reference: 3113039
The kits must in long race 44mm for scooter Minarelli horizontal liquid engine. Out of production!
Reference: 3113036
The original must race kit market. Out of production!
Reference: 3216827
Out of production !!!
Reference: 32 6867.10
Non-production do not buy. For information only. Pot MALOSSI MHR and MG MG3
Reference: 61 9004
Out of production. Replaced by the 61 7233 .
Reference: 23 8272B
Ideal in case of wear to start anew.
Reference: 2915497.W0
Spring which allows a more linear rise of your belt. Two models to choose from to adjust your transmission to perfection.
Reference: 6111703
Ideal for better cooling of your variation.
Reference: 51 7723
One of the variator makers for the general public.
Reference: 51 6840
MALOSSI Variotop drive for MBK GR2 and GR3 motor
Reference: 51 6498
MALOSSI Grande Plage variator for G2 and G3
Reference: 51 3125
MALOSSI Variotop Grande Plage drive Peugeot 103 engine spx G2 and G3
Reference: 5115501
One of the most famous drives in the world of two wheel relative to it's performance and strength.