Banner
The luxury version of the AIRSAL 50cc in two-segment, a powerful, solid, torquey kit and above all with an attractive price, very good basis for engine preparation.
Here is an excellent small 50cc kit from the house AIRSAL, the model that we call luxury is the TECH PISTON model which has a high-end two-segment piston, this kit also exists in a normal two-segment luxury model with us! This kit certainly has a low price but yet a quality and performance very present. 
The cylinder is therefore a Ø40.3mm nykasil treated aluminum, it has 5 transfers, the sides at the base are well worked, the internal sides are well designed and the exhaust is a large bar model. The diagrams which are quite low will agree perfectly with a small configuration type rebound exhaust with 17.5mm carburetor. The finish is not at the top but it remains very correct in relation to the price which is ridiculous ... 
The piston is therefore a luxury two-segment fine model including a chrome for the top, also of good quality its thin segments will allow it to push in high speeds (reduced friction) while preserving a minimum of torque, a good compromise performance! 
The cylinder head is a high compression with incoming stud in order to have a good alignment and a good holding of the cylinder head gaskets. The chamber is a hemispherical model with a polished finish. This cylinder head allows you, if desired, to reconnect the antifreeze to your carburetor. 
This cylinder comes with 2 base gaskets in order to place the desired squish. Clearly this cylinder is really a superb value for money! It will certainly be less efficient than a BIDALOT or ATHENA… But it will already remain very good.
We recommend it with at least: 17.5mm carburetion, air box preparation, racing exhaust, reinforced crankshaft and bearings, cold racing spark plug ... 
The pack contains:
-Cylinder aluminum 5 transfers exhaust bar
- Cylinder head has incoming high compression chamber
-Luxury bi-segment piston
-2 segments including a chrome for the top of the piston
- piston clips
-Piston pin
-Pack full seal
- Cylinder head screws
-Notice
As an option we offer you a stage 1 preparation, this preparation is a modification of the channels and the exhaust port by increasing the diagrams and improving the duct, it increases the performance of the cylinder. An improvement to the piston and the bottom of the skirt is also included in this modification. Allow a little extra time for this preparation!
Mounts on 50cc motorcycles with gearbox equipped with the minarelli am3, am4, am5, am6 euro 1, am6 euro 2 engine :
APRILIA RS 50cc am6 engine from 1997 to 2006 (new attention after 2006 in derbi euro 3 engine)
APRILIA RX am6 engine (attention news after 2006 in derbi euro 3 engine)
APRILIA MX am6 engine (attention news after 2006 in derbi euro 3 engine)
APRILIA TUONO 50cc am6 engine from 1997 to 2006 (new attention after 2006 in derbi euro 3 engine)
BETA RR
BETA RR ALU
BETA CRE
HONDA HM
HONDA CRE
HONDA BAJA
HUSQUVARNA WXE
HUSQUVARNA CH
HM DERAPAGE
HM CRE
MALAGUTI DRAKON
MALAGUTI XTM
MALAGUTI XSM
FANTIC CABALLERO
PEUGEOT XP6
PEUGEOT XPS
MOTORHISPANIA RYZ
PEUGEOT XPS
PEUGEOT XP STREET
PEUGEOT XP STREET EVO
PEUGEOT XR6
MOTORHISPANIA RX
PEUGEOT XR7
MOTORHISPANIA RX-R
RIAJU RS1
RIEJU RS2
RIEJU RS2 MATRIX
RIEJU RS2 MATRIX PRO
RIEJU SMX
RIEJU MRX
RIEJU SPIKE
KEEWAY TX FR
YAMAHA DT
MBK X-LIMIT
YAMAHA TZR
MBK X-POWER
SHERCO SM
SHERCO ENDURO
SHERCO HRD
SHERCO ENDURO
And many other machines!
Reference: 041332403
A single high compression cylinder head for kit 50cc AIRSAL Ø40.3mm. Ideal in case of breakage, crack or heater that just do the bolt will no longer be flat so a premature wear of the joints.
Reference: 061332403
A good quality piston comes complete for refurbishment of your cylinder.
Reference: 111332403
Segment high chrome range and already pre-rehearsed. A change every 5000 kms.
Reference: 3112199
A 50cc kit very powerful and solid, ideal for driving every day with reinforced crankshaft, 21mm carburetion, racing exhaust ...
Reference: 482036
The 50cc kit type origin the cheapest on the market with a quality and a correct finish.
Reference: CIL-788
Cylinder / piston without cylinder head ideal for meeting the 50cc engine and circulate daily. 7 transfers, extended oval exhaust, dual piston segments .... To accompany a cylinder head high compression BARIKIT.
Reference: IM1
New range of MVT cylinders for your MINARELLI AM6 engine!
Reference: 11000042
A powerful kit to install with a crankcase alignment and a good configuration low engine, exhaust and carburetion!
Reference: 129.0615/GT
Already available at our place, the newest member of FURYTECH! More powerful, more torquey, ...
Reference: 013006476
The deluxe version of 50cc AIRSAL bi-segment, a powerful kit, strong, torquey and especially with an attractive price, very good engine preparation base.
Reference: 479130
A kit with diagrams higher than the original with a cylinder head overcompréssée for a considerable performance gain while maintaining a very good strength.
Reference: H011381403
A kit a bit more powerful than the original while maintaining excellent reliability for a completely ridiculous price.
Reference: 032065
Here is a top engine of very good quality much cheaper than the origin which offers better heat dissipation, less friction...
Reference: KT00098
A high, solid and efficient 50cc engine. High quality and approved for daily circulation.
Reference: P400130100004
A kit that allows you to have torque at all speeds.
Reference: 504636
The latest from DOPPLER, the high cast iron engine which brings a very good performance gain while preserving the solidity and the legal displacement of 50cc.
Reference: 031000G
A small kit at a low price, nice, solid and efficient.
Reference: 11000168
An excellent 50cc kit, very powerful and very robust, ideal for competition as for the road!
Reference: 3112381
A high-performance kit reserved for competition in 50cc, diagrams very worked with a very studied architecture!
The luxury version of the AIRSAL 50cc in two-segment, a powerful, solid, torquey kit and above all with an attractive price, very good basis for engine preparation.
