Banner
Ideal together to improve performance, all at a lower cost!
Attention parts only reserved for the competition, prohibited on road!
We offer you the kit cylinder / piston without cylinder head 70cc Ø46mm cast in BARIKIT. It is cast iron and has 3 admission transfers and oval exhaust. 
The diagrams are quite low at admission and low enough to escape making the torquey and not difficult to follow or set. The piston is a two-segment model! Clearly this kit has a very good ratio torque / power, it offers plenty of performance while preserving a great strength! 
The piston is bi-model segments with segments for steels. We regret that it has no preparation on the rear apron to improve scanning and filling of admission. The finish is good. This kit will certainly be less effective than MALOSSI MHR, BIDALOT or Polini ... But there will already very good. 
We recommend to accompany this kit with: carburation 19mm crankshaft and reinforced bearings, exhaust racing, drive racing, racing candle, 100% synthetic oil ....
The pack contains:
X1 cylinder cast iron 3 transfers
X1 Piston bi-segments
X2 Segments, purpose, steel, 1mm thick
X1 Piston pin Ø10mm X 38mm
X2 piston Clips Type G
Pack X1 engine top seal 
Itself on:
HONDA 50cc VISION
KYMCO DJ
PEUGEOT Rapido 50cc
PEUGEOT ST
And many other models ... 
Optional we offer a preparation course 1, this preparation is a modification of the channels and the exhaust port by increasing the charts and improvement of the duct, it increases the cylinder performance. Improved piston and bottom skirt is also included in the amendment. Allow a little extra time for this preparation!
Specific References
Reference: P-328
The 46mm diameter piston replacement for kits 70cc cast BARIKIT! 5 ribs available bore.
Reference: JUN-705
A cheap pack complete joint for a winding up your engine!
Reference: S/37/2
Ideal for the maintenance of your cylinder / piston BARIKIT in 47mm diameter.
Reference: 02042848
Cylinder piston with segments for scooter HONDDA VISION 80cc.
Reference: 01022046
5 transfers exhaust with oval, bi-segment piston and cylinder head high compression 46mm in diameter, a good kit torquey and very strong!
Reference: CIL-730
A good kit without cylinder head, ideal to refurbish your engine with more performance!
Reference: 31 7132
A kit to mount the cylinder head of origin, performance and durability with low price!
Reference: 02041946
Powerful and strong, this 70cc is an excellent quality / price / power!
Reference: 31 7133
A solid, reliable and high torque engine!
Reference: 010224476
Escapement barrete, piston mono-segment, 47.6mm in diameter! A good little monster power!
Reference: 070600
A very powerful kit, even more powerful than the MALOSSI MHR REPLICA 70!
Reference: KT00058
A high engine without strong and powerful 70cc cylinder head, ideal for increasing your performance.
Reference: 010241476
This kit will offer more torque while keeping good reliability at a reasonable price.
Reference: CI.26.651.G
The only aluminum kit and the most powerful kit available for this engine architecture!
Reference: 31 8640
A kit certainly a little less powerful than a team but which can surprise more than one.
Reference: 02022046
Ideal in case of breakage, heating or motor clamp to a less expensive change.
Reference: 30425.M
A cylinder head without strong and torquey 70cc, ideal to optimize your performance. Equipped with 5 transfers, aluminum material with large exhaust and VERTEX piston mono segment.
Reference: 142.0147/R
A very well studied kit, touch up by hand to have as much performance as aluminum kits while enhancing the solidity of a cast iron kit.
Reference: 020224476
Ideal in case of breakage, heating or motor clamp to a less expensive change. If you already have a cylinder head 47,6mm.
Ideal together to improve performance, all at a lower cost!
