• Banner

Kit 95cc aluminum PARMAKIT Ø55mm for minarelli am6
  • Kit 95cc aluminum PARMAKIT Ø55mm for minarelli am6

95cc kit Ø55mm PARMAKIT aluminum for minarelli am6

53440.00

The biggest market kit for MINARELLI AM6 engine !!! A big Ø55mm diameter, 39mm in race to pose with a home run! A true torque monster.

Stage 1 engine preparation
€389.16
Quantity
Shipping in 5 to 10 days!

Description

Attention unapproved part on road, reserved exclusively for tours, runs ...

 

Here is a totally unique kit, although since there are already a number of years, this kit has never been copied or equaled side engine displacement ... Indeed, with its 55mm diameter mounted so original race 39mm, this kit offers no less real 92.61cc!

 


This kit is therefore mounted on all standard racing crankshafts therefore race 39mm 85mm rod. Ideal for those who did not want to resize their housing for the passage of a long-stroke crankshaft.

 

PARMAKIT has studied the room before the exit, they certainly put a Ø55mm bore in the cylinder but the skirt thickness is still very correct strength standpoint (2,25mm thick). This big bore recess must request a long race to talk ...

However d.55mm this kit is also short for 46mm travel available from us!

 


The advantage of keeping a race rod 39 so you aurrez easier to reach very high speeds. The cylinder was very worked, 5 admission transfers are present, one for the back (we all know that the rear transfer has hardly used the activation valves and scanning ...), the side are the number 4 and they are very bulky, plus on the front bottom as most hyper racing big brand cylinder. Exhaust level PARMAKIT opted to exhaust has booster, is best suited to couples of the beast, a large exhaust has booster is very well drawn on the cylinder. The piston is a true vertex in mono end segment (1mm) to fully release the high mode. It is a low domed piston crown.

 

 

This cast piston is a weight of 141 grams (complete with pin / segment / clips). For the cylinder head, it must extract heat from the thermal PARMAKIT group has opted for a cylinder head stud. Plot of machined cylinder head in the mass of high-quality aluminum, the room is a very suitable model to the piston / cylinder, hemispherical shape is polished, the pad is used to be sure that the alignment is always good tenth. The block incoming also avoids many head gaskets breakages! The cylinder head cover is also very well designed and has an excellent maintains! Anyway ... We could spend hours talking to you this nice monster we pulled out all the PARMAKIT, this kit was really neat to skirt cut point for improving the filling ... The whole thing is really a set quality, well-kept, large study. We have only two minor complaints to make, the exhaust outlet Ø28mm remains, however, a large minimum Ø34mm would be required to ask the proper exhaust ...

 


Following the example of packs BIDALOT FFM and other TPR aluminum 86cc already passed in Ø32mm. This minor complaint will not stop the good preparer will know who to talk this kit ... We also greatly appreciated the well-defined diagrams related to the set.

 


We recommend this kit with: reinforced crankshaft, 21mm minimum carburetion and quality with valves / pipe ... reinforced bearings, good cooling, efficient lighting, well reinforced clutch, cold candle racing exhaust unbridled ...

 


The pack contains:

X1 yoke stud

X1 pack attached with 3 joints of base plate for squish

X1 cylinder head cover

X1 aluminum cylinder 5 transfer nykasil d.55mm

X1 vertex piston mono segment d.55mm

X1 d.55mm segment chrome domed X 1mm hard

X1 axis 12mmX2 piston-type piston crab clips

X1 noticeX1 sticker ...


Spare parts:

pack joint with 3 joints of base plate for squish
cylinder head
Vertex piston mono segment d.55mm
d.55mm X 1mm hard chrome domed segment

Optional we offer a preparation course 1, this preparation is a modification of the channels and the exhaust port by increasing the charts and improvement of the duct, it increases the cylinder performance. Improved piston and bottom skirt is also included in the amendment. Allow a little extra time for this preparation!

This high engine fits the 50cc motorcycles following gearbox fitted the engine MINARELLI AM3, AM4, AM5, AM6 euro 1 am6 euro 2:

-APRILIA RS AM6 engine from 1997 to 2006 (after 2006, attention to motor past DERBI euro 3)
-APRILIA RX engine AM6 (after 2006, attention to motor past DERBI euro 3)
-APRILIA MX engine AM6 (after 2006, attention to motor past DERBI euro 3)

-Beta CRE

RR -Beta
-Beta RR ALU

-Honda HM
-Honda CRE
-Honda BAJA

-HUSQUVARNA WXE
-HUSQUVARNA CH

-HM DERAPAGE
-HM CRE
-MALAGUTI DRAKON

-MALAGUTI XTM
-MALAGUTI XSM

-FANTIC CABALLERO

-PEUGEOT XP6
-PEUGEOT XPS
-PEUGEOT XP STREET
-PEUGEOT XP STREET EVO
-PEUGEOT XR6
-PEUGEOT XR7

-MOTORHISPANIA RYZ
-MOTORHISPANIA RX-R
-MOTORHISPANIA RX

-RIEJU RS1
RS2 -RIEJU
-RIEJU RS2 MATRIX
-RIEJU RS2 MATRIX PRO
SMX -RIEJU
-RIEJU MRX
-RIEJU SPIKE

-KEEWAY TX EN

-YAMAHA DT
-MBK X-LIMIT
-YAMAHA TZR
-MBK X-POWER

SM -SHERCO
-SHERCO ENDURO
-SHERCO HRD
-SHERCO ENDURO

And many other machines!

Product Details
53440.00
New product

Specific References

ean13
8056590225554
You might also like
16 other products in the same category:

Reference: 01134950

AIRSAL

Kit 80cc Ø50mm AIRSAL luxury aluminum minarelli am6

A large diameter 50mm aluminum at a low price! This AIRSAL luxury version 80cc offers a lot of torque to the engine minarelli am6, compared to the original version, it has a piston high-end segment!

Price €158.33
Shipping in 1-3 days.
More
Shipping in 1-3 days.