• Banner

Kit 70cc Ø48mm PINASCO Racing aluminum minarelli am6
  • Kit 70cc Ø48mm PINASCO Racing aluminum minarelli am6

Kit 70cc Ø48mm PINASCO Racing aluminum minarelli am6

10059909

A high complete aluminum engine, efficient, solid and reliable, a real power monster little known to the general public.

Stage 1 engine preparation
€214.16
Quantity
Attention, may require a delay of more than 20 days

Description

Not approved on public roads, only reserved for competition, does not respect the highway code in any way!

Here is the new PINASCO racing aluminum kit Ø48mm, manufactured at GILARDONI, the largest cast iron in Italy! This kit is a monster of power ... Once again the proof that the power is not in the largest diameters but indeed in the finesse, the study, the diagrams and above all the quality!

Let's start with the cylinder, this model is therefore 48mm in diameter which offers real 70.57cc along with the original 39.00mm crankshaft stroke. This cylinder is a very high-end aluminum, the treatment is a nykasil GILARDONI therefore very high-end, the bore is perfect! It has 6 intake transfers which is very rare on minarelli am6 kits, its exhaust is a normal model certainly but very wide!

The diagrams are quite high, a large carburetion as well as a racing exhaust like the MALOSSI MHR GP 80, the MALOSSI MHR super motorcycle or other in the very racing type. The channels are well studied, the transfers are increased on the front in order to improve filling and sweeping. You should at best align the kit with your crankcases. The piston is a VERTEX racing model, hard chrome mono segment 1mm thick to allow the highest speeds, this piston has a very low crown bending angle.

This piston has a rear cutout improving filling. The cylinder head is in bie -partie (with stud) in order to obtain an optimal cooling, this cylinder head is polished hemispherical chamber, perfectly adapted to the piston. By the way, the compression ratio is 12/5 In short, PINASCO and GILARDONI have hit hard, this kit does not require any preparation in terms of diagrams, channels, transfers…. He is perfect! You will certainly have noticed the prepared skirt that is loose to optimize the sweep and fill.

Perfectionists will certainly bring a little finishing / polishing on the exhaust and the piston cap but the finish of this cylinder is impressive. We will only blame one thing, no joints of different thickness to properly adjust your squish!

We recommend mounting this kit with at least : minimum Ø21mm carburetion (24 recommended for maximum use), ignition supporting the turns, racing exhaust adapted to the 190 ° diagram, reinforced crankshaft, reinforced bearings, B10 spark plug, etc.

The pack comes with :

Installation instructions

Stickers

Cylinder 6 aluminum transfers normal exhaust Ø48mm

VERTEX piston single segment

Hard chrome domed segment Ø48mm X 1mm

Polished hemispherical cylinder head stud

Cylinder head cover

Piston pin Ø12mm

Piston clips Ø12mm crab

Complete seal pack

Reduction ring exhaust euro 1 to euro 2

...


As an option we offer you a stage 1 preparation, this preparation is a modification of the channels and the exhaust port by increasing the diagrams and improving the duct, it increases the performance of the cylinder. An improvement to the piston and the bottom of the skirt is also included in this modification. Allow a little extra time for this preparation!

This high engine is mounted on the following 50cc motorcycles with gearboxes equipped with the MINARELLI AM3, AM4, AM5, AM6 euro 1, AM6 euro 2 engine:

-APRILIA RS AM6 engine from 1997 to 2006 (after 2006, beware of engines passed in DERBI euro 3)
-APRILIA RX AM6 engine (after 2006, beware of engines passed in DERBI euro 3)
-APRILIA MX AM6 engine (after 2006, beware of engines passed in DERBI euro 3)

-BETA CRE

-BETA RR
-BETA RR ALU

-HONDA HM
-HONDA CRE
-HONDA BAJA

-HUSQUVARNA WXE
-HUSQUVARNA CH

-HM DERAPAGE
-HM CRE
-MALAGUTI DRAKON

-MALAGUTI XTM
-MALAGUTI XSM

-FANTIC CABALLERO

- PEUGEOT XP6
- PEUGEOT XPS
- PEUGEOT XP STREET
- PEUGEOT XP STREET EVO
- PEUGEOT XR6
- PEUGEOT XR7

-MOTORHISPANIA RYZ
-MOTORHISPANIA RX-R
-MOTORHISPANIA RX

-RIEJU RS1
-RIEJU RS2
-RIEJU RS2 MATRIX
-RIEJU RS2 MATRIX PRO
-RIEJU SMX
-RIEJU MRX
-RIEJU SPIKE

-KEEWAY TX EN

-YAMAHA DT
-MBK X-LIMIT
-YAMAHA TZR
-MBK X-POWER

-SHERCO SM
-SHERCO ENDURO
-SHERCO HRD
-SHERCO ENDURO

And many other machines!

Product Details
10059909
New product
16 other products in the same category:

Reference: 133.1008

POLINI

Kit 80cc Ø50mm POLINI Evolution aluminum minarelli am6

One of the rare competitors at the height of the TEAM MHR, this POLINI EVOLUTION offers a lot of torque and power, to accompany a good configuration!

Price €289.99
Please note, requires a delay of more than 20 days!
More
Please note, requires a delay of more than 20 days!

Reference: EQ-1034-S

BRK Competition Systems By BARIKIT

Kit 80cc Ø50mm BARIKIT BRK Racing 2 aluminum cylinder head minarelli am6

The famous 50mm (80cc) aluminum BARIKIT BRK Racing with high compression cylinder head with bi-part stud! A very powerful cylinder with 5 transfers worked, big exhaust with bar, piston mono segment ....

Price €241.66
Shipping in 7 to 12 days depending on BARIKIT factory arrivals
More
Shipping in 7 to 12 days depending on BARIKIT factory arrivals

Reference: 01134950

AIRSAL

Kit 80cc Ø50mm AIRSAL luxury aluminum minarelli am6

A large diameter 50mm aluminum at a low price! This AIRSAL luxury version 80cc offers a lot of torque to the engine minarelli am6, compared to the original version, it has a piston high-end segment!

Price €158.33
Shipping in 1-3 days.
More
Shipping in 1-3 days.