• Banner

  • -8%
Kit 80cc Ø50mm MALOSSI MHR replica aluminum minarelli am6
  • Kit 80cc Ø50mm MALOSSI MHR replica aluminum minarelli am6

Kit 80cc Ø50mm MALOSSI MHR replica aluminum minarelli am6

3112228

A ratio power / torque / unbeatable strength !!!

Stage 1 engine preparation
€274.99
€252.99
local_offer Save 8%
Quantity
Shipping in 1-3 days

Description

Not approved on the public highway, only reserved for the competition, in any case does not respect the rules of the road!

In the aluminum sports category we offer this kit MALOSSI MHR replica 80cc Ø50mm. This cylinder is the replica of the large MALOSSI MHR TEAM! This model is certainly slightly less powerful but also more torquey and strong! The cylinder head MALOSSI MHR TEAM of the stud has been replaced with a normal cylinder head, combustion chamber a truncated model st finish high compression blasted.


The cylinder is like MALOSSI MHR TEAM, a diameter of 50mm offers 76,57cc displacement (with the 39mm original race minarelli am6), this cylinder preserves the original base forms, transfers are 5 in number and they worked relatively well (front corner under the exhaust for better scanning performance and more). Transfers channels are studied, they require no preparation.


The exhaust is a model for boosters to maintain good strength while opening a maximum width exhaust. To slow the race for strength, MALOSSI posed a piston Bi segment, these segments are the top models of hard chrome domed range for less friction. The piston is a high-end model like all pistons MHR els, it has side oilers, it has a very high silicon content ...

A small cutting reopening of transfers shall bring back a better sweep (has them carried out by a trainer). This kit offers you the opportunity to reconnect antifreeze original carburetor, it is not mandatory of course. To conclude, this kit is a high-performance model but also very strong especially with treatment and bore MALOSSI MHR which are more upscale of the world! Whether for endurance, stunt ... this kit does not disappoint you! Ultra-torque, it also preserves very good high revs!



We advise to accompany this kit with at least: racing exhaust, carburetor 21mm, unbridled ignition, reinforced crankshaft, reinforced bearings, springs hard clutch ...

For information, the recommended resale price of 297.99 euros



The pack contains:

Cylinder MALOSSI MHR TEAM replica Ø50mm 5 transfers

Piston Ø50mm bi-segment

2 chrome segments hard curved Ø50mm X 1,5mm

Piston pin reinforced Ø12mm treaty

Piston Clips C Ø12mm

Boucheur antifreeze carburetor on head

Cylinder head high compression normal replica Ø50mm

Pack complete joint

Exhaust reducing ring euro 1 to euro 2

Explanatory Booklet / Guaranteed

stickers



Spare parts:

Cylinder MALOSSI MHR TEAM replica Ø50mm cylinder head with 5 transfers without piston


Piston Ø50mm bi-segment


2 chrome segments hard curved Ø50mm X 1,5mm


Piston pin reinforced Ø12mm treated with clips C


Piston Clips C Ø12mm


Boucheur antifreeze carburetor on head


Cylinder head high compression normal replica Ø50mm


Pack complete joint


Exhaust reducing ring euro 1 to euro 2




Optional we offer a preparation course 1, this preparation is a modification of the channels and the exhaust port by increasing the charts and improvement of the duct, it increases the cylinder performance. Improved piston and bottom skirt is also included in the amendment. Allow a little extra time for this preparation!

This high engine fits the 50cc motorcycles following gearbox fitted the engine MINARELLI AM3, AM4, AM5, AM6 Euro 1, Euro 2 AM6:

-APRILIA RS AM6 engine from 1997 to 2006 (after 2006, attention to motor past DERBI euro 3)
-APRILIA RX engine AM6 (after 2006, attention to motor past DERBI euro 3)
-APRILIA MX engine AM6 (after 2006, attention to motor past DERBI euro 3)

-Beta CRE

RR -Beta
-Beta RR ALU

-Honda HM
-Honda CRE
-Honda BAJA

-HUSQUVARNA WXE
-HUSQUVARNA CH

-HM DERAPAGE
-HM CRE
-MALAGUTI DRAKON

XTM -MALAGUTI
-MALAGUTI XSM

-FANTIC CABALLERO

-PEUGEOT XP6
-PEUGEOT XPS
-PEUGEOT XP STREET
-PEUGEOT XP STREET EVO
-PEUGEOT XR6
-PEUGEOT XR7

-MOTORHISPANIA RYZ
-MOTORHISPANIA RX-R
-MOTORHISPANIA RX

-RIEJU RS1
RS2 -RIEJU
-RIEJU RS2 MATRIX
-RIEJU RS2 MATRIX PRO
SMX -RIEJU
-RIEJU MRX
-RIEJU SPIKE

-KEEWAY TX EN

-YAMAHA DT
-MBK X-LIMIT
-YAMAHA TZR
-MBK X-POWER

SM -SHERCO
-SHERCO ENDURO
-SHERCO HRD
-SHERCO ENDURO

And many other machines!

Product Details
3112228
21 Items
New product
You might also like
16 other products in the same category:

Reference: EQ-987-S

BARIKIT

Kit 80cc Ø50mm aluminum BARIKIT Racing minarelli am6

A large diameter 50mm durable aluminum with 5 transfers and exhaust with bar, incoming high compression type of cylinder head. 50cc motorcycle equipped with the engine minarelli am6. Assured performance!

Price €195.83
Shipping in 7 to 12 days depending on arrivals BARIKIT
More
Shipping in 7 to 12 days depending on arrivals BARIKIT

Reference: 01134950

AIRSAL

Kit 80cc Ø50mm AIRSAL luxury aluminum minarelli am6

A large diameter 50mm aluminum at a low price! This AIRSAL luxury version 80cc offers a lot of torque to the engine minarelli am6, compared to the original version, it has a piston high-end segment!

Price €158.33
Shipping in 1-3 days.
More
Shipping in 1-3 days.