• Banner

Kit 78.5cc AIRSAL Xtrem red Ø50mm (special stroke 40mm) for minarelli am6
  • Kit 78.5cc AIRSAL Xtrem red Ø50mm (special stroke 40mm) for minarelli am6

Kit 78,5cc AIRSAL Xtrem red Ø50mm (special original race 39,2mm) for minarelli am6

01139150

A high performance ultra racing engine, all at a reasonable price. In addition to this, you need to know more about it.

Stage 1 engine preparation
€241.66
Quantity
Shipping in 20 to 90 days depending on factory arrivals.

Description

Here is the latest from AIRSAL! The Spanish brand is launched in a superb challenge, to release a high ultra racing engine, very powerful in an unbeatable price. Successful bet as proof with this high real AIRSAL Xtrem 78.5cc Ø50mm red engine. This model is really beautiful, powerful and ingenious, all for a very reasonable price.

The cylinder is therefore a Ø50mm, it is mounted with an original race crankshaft. This cylinder is not only painted red, it is an entire architecture that has been created! The rear admission receives 3 transfers in order to improve the sweep, the lateral ones are 2 in number and they are well worked overall. The exhaust is a very large bar model. Nykasil is a trivial scanimet (we will still prefer a high-end coating like hard nykasil but it is already of good quality). We can classify the cylinder as the entry level of hyper racing.

The diagrams are high in order to offer maximum performance at high revs. The cylinder head is an ordinary one-piece, we would still have preferred a stud bolt to improve cooling and changes in volumes, shapes… But this cylinder head monobloc will already amply satisfy 99% of users! The chamber is a high compression hemispherical model with a polished finish.

The piston is in the form of the ordinary VERTEX model that is often found on AIRSALs, it is of very good quality and it is specific by a treatment on the anti-detonation cap. The piston is equipped with side grease nipples which is also very appreciable for longevity. The attached pack is complete but you will still lack base gaskets to make the squish as it should be which is regrettable!

To conclude, this set is really superb value for money! The performances will be there for sure with such a high engine. It is clear that users who really want very polished material will regret the absence of solid studs with nuts, a hard nykasil, a stud bolt, gaskets to make the squish correctly, ...

But for such a price we couldn't expect anything better than what AIRSAL did! The finish will certainly amaze you! It is worthy of the greatest BIDALOT, MHR ... See even better!

We recommend with this kit at least: Ø28mm carburetion, reinforced crankshaft original stroke 39.2mm, reinforced bearings, suitable exhaust, low engine / high engine alignment, ignition according to the revs, cold spark plug grade B10 (31 in DENSO) see B105 ( 34 in DENSO), ...

The pack contains:

Screw set
Notice
Sticker
Cylinder d.50mm 7 AIRSAL Xtrem transfers
Special VERTEX piston with anti-detonation treatment ANODIZING TREATMENT
Segment
Complete seal pack
Cylinder head with incoming chamber Ø50mm high compression
Piston pin
2 racing piston clips in C


As an option we offer you a stage 1 preparation, this preparation is a modification of the channels and the exhaust port by increasing the diagrams and improving the duct, it increases the performance of the cylinder. An improvement to the piston and the bottom of the skirt is also included in this modification. Allow a little extra time for this preparation!

This high engine is mounted on the following 50cc motorcycles with gearboxes equipped with the MINARELLI AM3, AM4, AM5, AM6 euro 1, AM6 euro 2 engine:

-APRILIA RS AM6 engine from 1997 to 2006 (after 2006, beware of engines passed in DERBI euro 3)
-APRILIA RX AM6 engine (after 2006, beware of engines passed in DERBI euro 3)
-APRILIA MX AM6 engine (after 2006, beware of engines passed in DERBI euro 3)

-BETA CRE

-BETA RR
-BETA RR ALU

-HONDA HM
-HONDA CRE
-HONDA BAJA

-HUSQUVARNA WXE
-HUSQUVARNA CH

-HM DERAPAGE
-HM CRE
-MALAGUTI DRAKON

-MALAGUTI XTM
-MALAGUTI XSM

-FANTIC CABALLERO

- PEUGEOT XP6
- PEUGEOT XPS
- PEUGEOT XP STREET
- PEUGEOT XP STREET EVO
- PEUGEOT XR6
- PEUGEOT XR7

-MOTORHISPANIA RYZ
-MOTORHISPANIA RX-R
-MOTORHISPANIA RX

-RIEJU RS1
-RIEJU RS2
-RIEJU RS2 MATRIX
-RIEJU RS2 MATRIX PRO
-RIEJU SMX
-RIEJU MRX
-RIEJU SPIKE

-KEEWAY TX EN

-YAMAHA DT
-MBK X-LIMIT
-YAMAHA TZR
-MBK X-POWER

-SHERCO SM
-SHERCO ENDURO
-SHERCO HRD
-SHERCO ENDURO

And many other machines!   In addition to this, you need to know more about it.

Product Details
01139150
New product
You might also like
16 other products in the same category:

Reference: EQ-987-S

BARIKIT

Kit 80cc Ø50mm aluminum BARIKIT Racing minarelli am6

A large diameter 50mm durable aluminum with 5 transfers and exhaust with bar, incoming high compression type of cylinder head. 50cc motorcycle equipped with the engine minarelli am6. Assured performance!

Price €195.83
Shipping in 7 to 12 days depending on arrivals BARIKIT
More
Shipping in 7 to 12 days depending on arrivals BARIKIT