Cylinder / piston without cylinder head 50cc Ø40,3mm BARIKIT iron minarelli am6

Approved on the public highway, respect the required displacement of 50cc. To accompany a high compression cylinder head BARIKIT specific to this cylinder.

Here is a very good kit 50cc cast iron for mécaboite Minarelli AM6 engine, it is the BARIKIT model with a bore diameter Ø40,30 mm without cylinder head. This model therefore offers cast iron 50cc regulatory capacity of torque and power to be in order and move every day, thanks to solid cast alloys.



Its cast iron cylinder thus has 7 transfers inlet 1 in the rear side and 6. Admission is reworked, we recommend also to mount 17,5mm PHBG carburetor to the cylinder 19mm if you see slightly rework admission, the exhaust outlet is also much improved with its expanded output. Diameter of the exhaust outlet Ø28 mm wedge for passage to a diameter Ø 25 mm not included.



Charts well studied for this little cast thus providing slight performance and greatly improved recovery compared to the original model, especially coupled with good compression ratio offered by the hemispherical combustion chamber of the cylinder head BARIKIT.



This kit does not neglect the couple and solidity with its dual-piston segment well-designed, two chrome resistant segments promoting the couple as well as the ramp-up due to the delicacy of the latter (1 mm). The advantage of this all is its relatively low price, you will have a powerful engine, torquey and very strong! A very good basic preparation also for the connoisseurs who want to have fun every day or run on circuit.



We advise you to accompany this high engine with at least: 17.5 mm carburetor, intake pipe flexible mounting racing, BARIKIT high compression cylinder head, crankshaft and reinforced bearings for the better and start on a completely new engine and without problems, cold candle racing, 100% synthetic engine oil, relaxing escape ....

The pack contains:

-cylinder Sports cast Ø40,30 7 mm transfers and exit oval exhaust
-piston 40.30 mm bi segment
-2 Segments purposes chrome thickness 1 mm
Axis-piston Ø12 X 33 mm
Crab-like piston -Clips
-pack Complete joint



Optional we offer a preparation course 1, this preparation is a modification of the exhaust port by increasing the charts and improvement of the duct, it increases the cylinder performance. Improved bottom skirt is also included in the amendment. Allow a little extra time for this preparation!

This high engine fits the 50cc motorcycles following gearbox fitted the engine MINARELLI AM3, AM4, AM5, AM6 euro 1 am6 euro 2:

-APRILIA RS AM6 engine from 1997 to 2006 (after 2006, attention to motor past DERBI euro 3)
-APRILIA RX engine AM6 (after 2006, attention to motor past DERBI euro 3)
-APRILIA MX engine AM6 (after 2006, attention to motor past DERBI euro 3)

-Beta CRE

RR -Beta
-Beta RR ALU

-Honda HM
-Honda CRE
-Honda BAJA

-HUSQUVARNA WXE
-HUSQUVARNA CH

-HM DERAPAGE
-HM CRE
-MALAGUTI DRAKON

-MALAGUTI XTM
-MALAGUTI XSM

-FANTIC CABALLERO

-PEUGEOT XP6
-PEUGEOT XPS
-PEUGEOT XP STREET
-PEUGEOT XP STREET EVO
-PEUGEOT XR6
-PEUGEOT XR7

-MOTORHISPANIA RYZ
-MOTORHISPANIA RX-R
-MOTORHISPANIA RX

-RIEJU RS1
RS2 -RIEJU
-RIEJU RS2 MATRIX
-RIEJU RS2 MATRIX PRO
SMX -RIEJU
-RIEJU MRX
-RIEJU SPIKE

-KEEWAY TX EN

-YAMAHA DT
-MBK X-LIMIT
-YAMAHA TZR
-MBK X-POWER

SM -SHERCO
-SHERCO ENDURO
-SHERCO HRD
-SHERCO ENDURO

And many other machines!