Reference: 56260.16
PARMAKIT segment d.46 X 1.5mm chrome ground for 70cc aluminum kit on Peugeot 103 / fox / wallaroo
Replacement hard chrome segment diameter 46mm, thickness 1.5mm for kit PEUGEOT 103, FOX, Honda Wallaroo...
Banner
Attention, not approved and prohibited on the road, reserved only for competition.
* Aluminum cylinder head gasket no longer supplied with the cylinder. Mounts with O-ring now!
**Warning!!! The compression ratio should not exceed 12.7: 1, before the first start, check your chamber volume, it should be around 5.6ML / CC excluding spark plug wells!
Attention, for PEUGEOT FOX and HONDA wallaroo a special kit is now available, this model must not be fitted which is intended for PEUGEOT 103 only.
A very good kit made in Italy, really very high-end and relatively solid, in high quality aluminum treated with nykasil, bore Ø46mm, real 64.98, short piston in single segment. It has 6 transfers, the side transfers at the joint plane are quite large. It is very similar to the famous aluminum malossi except that it is in mono segment 1.5mm thick, 46mm in diameter.
The diagrams, the exhaust width, the finish ... make it a very powerful kit. The exhaust is normal without boosters or bars in order to preserve torque and strength but it is still really very powerful also at high speed. The turns are the most sought after on this type of kit in relation to a lot of 70cc, the piston has a rear preparation to open the rear transfers a ¾ in order to create a better sweep flow to have the maximum torque, a little kit known in France but to try, its performances are astonishing.
The rear transfers are enlarged in length so that the filling is better and to go with the piston preparation. For the finish we will give a note 7/10. This kit is complete and therefore delivered with a well adapted cylinder head, this cylinder head offers superb cooling, a very good squish zone, a good compression ratio… Clearly! This set is perfect, very well priced, and it won't disappoint.
the pack contains :
-an aluminum cylinder d.46mm 3 large transfers outside and 6 inside
-a piston mono segment with d.46mm
-a reinforced axis with anti-wear treatment, original diameter 12mm
-2 piston clips (pin ring) crab type
-1 segments reinforced chrome base s10
-O-ring cylinder head gasket
- paper base gasket
- copper exhaust gasket
-High compression air cylinder head Ø46mm
We recommend it with at least : racing exhaust, racing carburetion (19mm mini), reinforced bearings and crankshaft, casing preparation.
As an option we offer a stage 1 preparation, this preparation is a modification of the channels and the exhaust port by increasing the diagrams and improving the duct, it increases the performance of the cylinder. An improvement to the piston and the bottom of the skirt is also included in this modification. Allow a little extra time for this preparation!
Specific References
Reference: 56260.16
Replacement hard chrome segment diameter 46mm, thickness 1.5mm for kit PEUGEOT 103, FOX, Honda Wallaroo...
Reference: 56207.02A
The replacement piston for 46mm aluminum PARMAKIT air or liquid kits on 103, fox, wallaroo.
Reference: 56207.03
Pack seal for kit 70cc 46mm PARMAKIT AIR.
Reference: 56207.04
An excellent cylinder head, in addition to being rare it is very efficient and its cooling is really excellent!
Reference: 2200.38
Premium Viton O-ring for less friction and better sealing of your cylinder head.
Reference: 31 8393
high-end kit well worked with excellent finishes.
Reference: 142.0089
Ideal for a small couple configuration! Original size transfers, solidity, simplicity, guaranteed performance POLINI !
Reference: CI.26.650.G
Overpowered kit on the verge of extinction. Out of production!
Reference: 002300
Super solid with its aluminum and its very high quality processing, its architecture also allows very good performance.
Reference: 56207.00
A very good rare and powerful kit to be accompanied by a good high compression cylinder head in Ø46mm.
Reference: 56215.00
The biggest kit on the market for 103, or should we say huge? A completely exceptional preparation base for experienced people who know how to make the engines speak!
Reference: 56209.00
The biggest kit on the market for 103, or should we say huge? A totally out-of-the-ordinary preparation base for experienced riders who know how to make the engines talk!
Reference: CIL-962-S
Although relatively uncommon, this kit did nothing specific.
Reference: 142.0088
A superb kit, 6 transfers with a W-shaped exhaust, 46mm in diameter in aluminium, power with a world-renowned kit for your 103!
Reference: 31 8384
The well-known MALOSSI cast iron 70cc. Solid, torquey, not neglecting power, it is an ideal companion for long endurance trips where performance is required.
Reference: 31 8388
Very good kit level performance, torque and quality always at the rendezvous.
Reference: 56220.00
A highly anticipated watch, rare and well-structured cylinder! A nice base for those who don't like to do like everyone else.
Reference: 003200
Out of production.
Reference: 02022546
A kit at a low price and yet very efficient in addition to being a very good basis for preparation with its exhaust has boosters, its 6 transfers and its mono-segment (or bi-segment).
Reference: KT00073
Super strong and torquey, the only 70cc kit with the ATHENA which is very well suited to crankcases with 2 transfers!
Reference: 02020846
The super torquey kit that does not require large equipment or headaches!