Reference: 285.0100
2 crankshaft spy joints reinforced with foam, original size POLINI for Peugeot 103
Set of 2 high-end competition POLINI oil seals for Peugeot 103.
Banner
Here is a very economical part! This set of housings is really complete and all for a ridiculous price ...
Ideal to start afresh! Ideal for making good engine preparation on a clean base, especially since this set of housings is very thick and leaves room for machining! The housings are Peugeot 103 type models, they are not the real Peugeot housings ....
They are a different exterior shape, the alloy is of high quality, the workings are good and the finish is passable. They are delivered with a high quality viton spy seal set, an ignition foam, a set of reinforced folded steel cage bearings (to be changed if you have a large configuration).
There is also a spy plate for the drive side with its screws. We regret all the same that the bearings are pre-assembled!
In mechanics normally we put the bearings on the vilo to then mount the vilo on the previously heated casings for assembly without forcing!
This pack also has a crankcase gasket, high quality reinforced 4 stud base gasket and all the crankcase screws / washers / nuts !!!!
Be careful, manufactured in Turkey, unlike CGN casings, these casings are of lower quality and are hollow, they are not suitable for preparation such as alignment with a large transfer cylinder (AIRTSAL T6). We have a clear preference for CGNs!
The pack contains:
X1 set of reinforced riveted steel cage bearings
X2 full original type engine casings
X2 seals spy racing viton
X1 foam on the ignition side
X1 set of 4 studs
X1 complete set of screws
X1 complete washer set
X1 complete nut set
X1 drive spy support plate
X2 screws for drive plate
x1 base gasket
x1 crankcase gasket
x6 washers
On mounting on PEUGEOT 103.
Reference: 285.0100
Set of 2 high-end competition POLINI oil seals for Peugeot 103.
Reference: 638
An original type gasket for original crankcases at low prices.
Reference: 188888
The cheapest spy + bearing complete set for Peugeot 103! Nevertheless, the quality is there!
Reference: 263162
Bolts with quality steel and a wide choice of sizes!
Reference: 8933
Good quality nuts with several sizes available to adapt to the best.
Reference: 685
A seal of high quality at low cost for safe motor and leakage!
Reference: 683
Ideal for reassembling its leak for a more reliable engine. Ideal for 3 transfers, small or large ...
Reference: 485343
A reinforced stud from CGN, ideal in case of breakage or wear of your old stud. Maximum tightening 16nm or 1.63mk / g.
Reference: usinage-54mm-carter
Machining for passage of Ø50mm cylinders on MBK 51, PEUGEOT 103, ...
Reference: 168300
Engine housings with a very good quality / price ratio. Ideal for a total refurbishment of your Peugeot 103.
Reference: 32020640
Engine housings with a very good quality / price ratio. Ideal for a total refurbishment of your PEUGEOT 103.
Reference: 170.0060
Large crankcases with large intake and support in "bare" version for your 103!
Reference: 57 4275
Carter MALOSSI MG2 and MG3 for Peugeot 103
Reference: 170.0010
The excellent small POLINI housings for 103!
Reference: CMG2B 103
Competition engine casings for PEUGEOT 103 with PEUGEOT G2 engine base
Reference: usinage-CL-carter
Machining for passage of long stroke crankshafts on MBK 51, PEUGEOT 103, ...
Reference: 57 5208
The must of the crankcase for 103, a very powerful design, an unequaled quality!
Reference: 56209.50
Housings adapted for the 77cc Ø50mm kit for 103.
Reference: 170.0020
The bare version without bearings, spy joints or studs, all the same delivered with pipe, valves ...
Reference: 093020
The famous CARENZI RACING crankcases, excellent value for money!
Reference: 170.0050
Known and renowned housings from POLINI. This pack is renowned and above all complete which allows a considerable financial advantage.
Reference: 170.0080
Very well known housings in the middle of the 103 because very well worked and finished for a price that has earlier affordably seen the quality of the housings.
Reference: 170.0090
The famous big casings for SPX / RCX / MVX and CLIP, version without bearings, neither joints spy, nor studs!
Reference: 57 6548
Super performing housings, which allow to pass the admissions of motorcycle DERBI and MINARELLI AM6 on your PEUGEOT 103, quality at the top! Built-in support!